Consider a broadcast channel with N nodes and a transmission rate of R bps. Suppose the broadcast channel uses polling (with an additional polling node) for multiple access. Suppose the amount of time from when a node completes transmission until the subsequent node is permitted to transmit (that is, the polling delay) is dpoll. Suppose that within a polling round, a given node is allowed to transmit at most Q bits. What is the maximum throughput of the broadcast channel?

Consider a broadcast channel with N nodes and a transmission rate of R bps. Suppose the broadcast channel uses polling (with an additional polling node) for multiple access. Suppose the amount of time from when a node completes transmission until the subsequent node is permitted to transmit (that is, the polling delay) is dpoll. Suppose that within a polling round, a given node is allowed to transmit at most Q bits. What is the maximum throughput of the broadcast channel?

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter20: Queuing Theory

Section20.10: Exponential Queues In Series And Open Queuing Networks

Problem 8P

See similar textbooks

Similar questions

Consider a broadcast channel with N nodes and a transmission rate of R bps. Suppose the broadcast channel uses polling (with an additional polling node) for multiple access. Suppose the amount of time from when a node completes transmission until the subsequent node is permitted to transmit (that is, the polling delay) is ?poll. Suppose that within a polling round, a given node is allowed to transmit at most Q bits. What is the maximum throughput of the broadcast channel?
2. Consider a bus-topology network with five stations. A reservation access method is used. Each station has infinite data to transmit. Each reservation slot has 10 microseconds (note that 1 microsecond = 106 second). For each station, one data transmission sends 1000 bits. The transmission rate over the medium is 10 Mbps. For a station, which is its throughput (in unit "Mbps")?
Consider the following scenario: Frames of 12000 bits are sent over a 400kbps channel using a satellite whose propagation delay is 270ms. Acknowledgements are always piggybacked onto data frames. (That is, in the case of stop-and-wait, the next frame cannot be transmitted until the entire frame containing the acknowledgement is received.) Five-bit sequence numbers are used. What is the maximum achievable channel utilization for (a) Stop-and-wait. (b) Protocol 5 (i.e., Go Back N). (c) Protocol 6 (i.e., Selective Repeat)
Consider the following network with given line speeds and lengths: Assume the speed of light is 2×10^8 m/s, and that the processing and queuing delays are negligible. Node A sends a 1400-byte frame to node C through node B. Suppose Node A starts sending the first bit of the frame at t=0. Answer the following questions: a. At what time (t=?) node B receives the frame in full (i.e. the last bit)? b. After node B receives the frame in full, then it will start sending the frame to node C. Determine the time (t=?) when node C receives the frame in full. c. Suppose at this time node C sends a small acknowledgment back to node A. The transmission time for the acknowledgment is negligible. Calculate at what times (t=?) the acknowledgment arrives at nodes B and A. d. Assume after sending its frame, node A wait for the acknowledgment back from node C before sending the next frame. What is the average throughput (number of transmitted bits per second) of the data flow from node A to…
Frames of 1000 bits are sent over a 106 bps duplex link between two hosts. The propagation time is 25 ms. Frames are to be transmitted into this link to maximally pack them in transit (within the link). 1.1 What is the minimum number of bits (1) that will be required to represent the sequence numbers distinctly? Assume that no time gap needs to be given between transmission of two frames.
Suppose that a SW ARQ system with 1-bit sequence numbering has a time-out value that is less than the time required to receive an ACK. Station A sends 5 frames to station B. No errors occur during transmission of all 5 frames. One ACK is lost when it is transmitted the first time (see the following table), and no transmission of that ACK. No errors occur during transmission of the other 4 ACKS. Sketch the sequence of frame exchanges that transpire between stations A and B. (а) error occurs in re- Last digit of your student ID number 0, 1 2, 3 Lost ACK 1 4, 5 6, 7 8, 9 2 3 4
In a two-phase, total-order multicast system, messages are sent in the following sequence from node S to G1 and G2. G1 and G2 are the members of the group. S sends m1 to G1 S sends m1 to G2 S sends m2 to G2 S sends m2 to G1 Use the basic implementation of the Lamport clock. The clock s at each node start at: S: 4, G1: 6, G2: 1. Show the exchange of messages and their acknowledgments in a clock diagram using the basic implementation of Lamport's clock. In which order and at what times are m1 and m2 delivered?
Consider a network with a ring topology, link bandwidths of 100 Mbps, and propagation speed 2 × 108 m/s. What would the circumference of the loop be to exactly contain one 1500-byte packet, assuming nodes do not introduce delay? What would the circumference be if there was a node every 100 m, and each node introduced 10 bits of delay?
Consider two hosts S and R connected directly by a link. A link has a transmission speed of 107 bits/sec. It uses data packets of size 400 bytes. Data needed to transmitted is 400 bytes. Length of the link is 600 km and the propagation speed are 3 × 108 meter per second. T is the transmission delay and P is the propagation delay. The propagation delay in millisecond and transmission delay in microsecond respectively are
Suppose nodes A and B are on the same 10 Mbps broadcast channel, and the propagation delay between the two nodes is 245 bit-times. Suppose A and B send Ethernet frames at the same time. Suppose the transmission time of the entire frame is 295 bit-times. So, the frames collide, and then A and B choose different values of K in the CSMA/CD algorithm. A node chooses the value of K at random from {0,1,2,...2n−1} where n is the number of collisions experienced on the channel – note n is set to 1 in this case). For Ethernet, the actual amount of time a node waits is K*512 bit times (i.e., K times the amount of time needed to send 512 bits into the Ethernet). Suppose A chooses a K value of 0 and B chooses a K value of 1. Assuming no other nodes are active, can the retransmissions from A and B collide? Justify your answer by showing all the intermediate steps of your calculations.
A link has a transmission speed of 106 bits/sec. It uses data packets of size 1000 bytes each. Assume that the acknowledgment has negligible transmission delay, and that its propagation delay is the same as the data propagation delay. Also assume that the processing delays at nodes are negligible. The efficiency of the stop-and-wait protocol in this setup is exactly 25%. The value of the one-way propagation delay (in milliseconds) ?
Consider two nodes (A, B) sharing the same broadcast channel of speed R =10Mbps. The propagation delay between the two nodes is 1ms. Consider a node C in the middle between both nodes. If A starts at time t=0 its transmission of a packet to node C, at what time can node B start transmitting its packet to a node D in the network in order for the two packets not to collide? Assume both nodes have each a packet of length L = 1000Bytes. О а. 1.3ms O b. 1ms О с. 0.5ms d. 1.8ms