Consider a 3-story frame with 13' story heights. The frame captures a 20' tributary depth for wind loads. The windward pressures are given in the table. Calculate the resultant force at each story. When ready, proceed to the next item in the module to submit your answers and a scan of your work. Height [ft] Pressure, p [psf] 39 30 20 15 0 20.51 19.04 16.86 15.50 15.50

Consider a 3-story frame with 13' story heights. The frame captures a 20' tributary depth for wind loads. The windward pressures are given in the table. Calculate the resultant force at each story. When ready, proceed to the next item in the module to submit your answers and a scan of your work. Height [ft] Pressure, p [psf] 39 30 20 15 0 20.51 19.04 16.86 15.50 15.50

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4) Select the size of a timber joist with notched end as shown below. The notch is set at 1/3 of the joist depth. The load acting on the joist is 50 kg/m. The deflection limit is set at L/240.The joist is sitting on masonry wall with the width of 15 cm. Assume dense timber. Check all the limit states. 50 kg/ m H 2/3Н 5 m
Please help, I promise to give good feedback. Please do not just guess. Thank you!
Show neat and clean step by step solutions. Also show FBD if possible.
1. How much is the area under shear from point of zero to point B?
A line is recorded as 475.25 m long. It is measured with a 6.5 N tape which is 30.492 m long at 680F under a 10 lb. pull supported at end points. During measurement the temperature is 4.50C and the tape is suspended under a 71 N pull. The line is measured on 3% grade. What is the true horizontal distance? Modulus of elasticity of the tape is 1.93 X 108 KPa and cross-sectional area of tape is 0.0284 cm2. Coefficient of expansion of the tape material is 0.0000116 m/0C.
A uniform 12.0 kq door with dimensions 75cm x 200 cm is Pivoted at hinges' 25 cm from the top and from the bottom. A.) Find the hori zontal force B.) Find the vertical force exerted by each hinge.
Q2: Determine the resultant force and its direction on the gate shown: Sal. 2m Reim
Question in Picture
find the load (kips) for the top floor to two decimals find the load (kips) for the middle floor to two decimals find the load (kips) for the bottom floor to two decimals
Situation No. 1: A 5 storey building is constructed with 15 ft. storey heights. The base shear has been calculated as 165 kips. Each story floor has weight of 700 kips. If the natural period of oscillation is 0.60 sec. Compute the shear at the 5th floor. Compute the shear force at the 4th floor 3. Compute the shear force at the 3rd floor.
Question 12 Problem 12: The plan view (90' x 120) of a three-story reinforced concrete building is shown in Fig, 6. All columns are 2-ft squares and are centered on the grid lines. The concrete floors and roof are one-way slabs supported on the beams. The floor live load is 50 psf, and the roof live load is 15 psf. Assuming no live load reduction, the service live load, LL (kips), on an interior column at its base on the ground level is most nearly: 40 Column = 2' x 2' (typical) 40 40' 30' 30 30' Fig. 6- Plan view for Problems 11 & 12 O 140 O 180 O 54 O 240
Kindly answer carefully. Please show all the necessary steps