1. If the compressive force of AD is 12KN, what is the value of F.2. If the compressive force of AD is 12KN. What is the compressive force of member CD and BD. Question 37/50If the compressive force on member AD is 12 kN.Which of the following gives the nearest value ofcompressive force on member BD ?11.97 kNO 16.22 kNO 15.85 kNO 18.65 kN Question 36/50Situation 36, 37 and 38SmSmIf the compressive force on member AD is 12 kN.Which of the following gives the nearest value of forceF?40.25 kN29.60 kN50.65 kN38.99 kN

To Determine force of member CD and BD. Value of F

Answered: If the compressive force of AD is 12KN,…

If the compressive force of AD is 12KN, what is the value of F. 2. If the compressive force of AD is 12KN. What is the compressive force of member CD and BD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.250 in. thick, and made of aluminum that has an elastic modulus of E = 10,100 ksi. Assume that a = 16 in., b = 27 in., c = 11 in., and d = 20 in. Determine the maximum magnitude of load P that can be applied to the rigid bar without causing member (1) to buckle.
Jertical beam of the applied to a shown. Determine forces are cross section compressive BC of the the maximum Stresses bRam. tensile and portion. 9,25 kN in 45mm I10mm 30 mm 30mm 400mm 500mm
25. Design stress is less than the ultimate strength. O 26. If the internal bending moment is negative, the beam bends concave upward. O True False O O True False 27. If the internal shear is negative, the beam bends concave downward, True False
We are given the statically indeterminate structure shown in Figure 2. Apart from the loadings, member AB is also subjected to temperature effects. The cross-sectional depth of member AB is h = 12 in, and the thermal coefficient is aT= 5:10-6 /° F. We are also given that the effect of axial forces on the deformations can be NEGLECTED. 1 kip/ft 5 kip BV VVvvvwwW EI = 8:105 kip-ft2 EI = 106 kip-ft2 20 ft Figure 2 a) Establish a primary structure b) Establish the compatibility equation from which you will obtain the redundant force c) Determine the support reactions of the structure d) Determine the internal loading diagrams of the structure e) Determine the support reactions IF THE STRUCTURE IS ONLY SUBJECTED TO THE TEMPERATURE EFFECTS (and not the loads) AT: = 5 °F ÅT;= -5 °Fi
Beam AB is supported as shown in the figure. Tie rod (1) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A, B, and C each have an ultimate shear strength of 57 ksi, and tie rod (1) has a yield strength of 33 ksi. A concentrated load of P = 14 kips is applied to the beam as shown. A factor of safety of 2.4 is required for all components. Determine: (a) the minimum required diameter for tie rod (1). (b) the minimum required diameter for the double shear pins at B and C. (c) the minimum required diameter for the single shear pin at A. 6.7 8 in. 3.8ft (2) 8.5ft
5 in? in. 3 in? 1 in? 500 lb. 1500 Ib. 20 in. 20 in. 20 in. E = 29 x 106 psi Member 1 2 3 a) Develop the system stiffness matrix for the three element bar shown. b) Use the applied loads and boundary condition to develop the restrained system stiffness matrix with the applied loads c) Find the deflections at each node d) Solve for the internal forces in each rod element e) Compute the strain energy in the structure. f) Verify the results that you found for c) by using classical approach, õ=(P.L)/(A.E)