concrete lined rectangular channel 5.5 m wide carries water at a rate of 10 m3 /s. Calculate critical velocity in m/s if the channel bed is having a slope of 1 in 2000. Take Manning’s constant N = 0.01.   Answers: a.1.044 b.0.696 c.0.216 d.2.613

Q: A 0.3 m diameter pipeline terminates nozzle of outlet diameter = 0.15 m. The free jet from the…

A: Dia of pipeline = 0.3 mOutlet diameter = 0.15 mDeflection of Jet = 90 degreeDischarge of water =…

Q: kg-crate travels down the path as shown below. Determine the magnitude of the work done (J) by the…

A: Given:- weight of crate = 29.21 kgcrate speed at A= 91.44 cm/scrate speed at B = 7620 mm/s To find:-…

Q: Figure below is a representation of the Altus gravity dam in Oklahoma. Find the magnitudes and…

A:

Q: At a section in a channel expansion, the velocity over 25% of the cross-section is zero and it is…

A: Velocity over  of cross section is zero.The remaining area has uniform velocity.To find: Momentum…

Q: Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm)…

A:

Q: 2. A pitot-static tube (C=1.0) is used to measure air speeds. With water in the differential…

A: Density of air and head water is given and it has been asked to determine velocity through pitot…

Q: Q10. A 3.9-kg collar travels down a smooth slope as shown. The spring has unstretched length of 8 m…

A: Given- m = 3.9 kg l  = 8 m  k = 29 N/m S1 = 15 m  S2 = 9m

Q: elect one: O a. 46.33 m O b. 37.18 m c. 42.51 m O d. 51.56 m

A: Given data- Roughness coefficient (f) = 0.015 Length (L) = 80m Diameter (D) = 0.150m Discharge (Q)…

Q: SITUATION 3. A 75mm DIAMETER ORIFICE DUNDER THE HEAD OF 5m DISCHARGES OIL WITH SG = 0.81. IF THE…

A: We will use formula of Cv and Head loss.

Q: Calculate the components of the hydrostatic force exerted by the water on a (1 m) width of the…

A: To find component of Hydrostatic force

Q: A 500 mm diameter concrete pipe is laid on a slope of 1 m per kilometer and is filled with water at…

A: The slope is S=11000. The diameter of the pipe is D=500 mm. The manning coefficient is n=0.0125.…

Q: A 100-ft long dam holds 30 ft of water as shown in the figure. L= 100 ft. w.s. 30 ft. 609

A:

Q: = 0.0220 c v rate is 0. ake g= 9.8

A:

Q: N/m 1.750 N/m 2,7 m

A:

Q: A pipe bends through (48)° from its initial direction as shown in Figure C. The diameter of the pipe…

A: Angle of bend = 48° Fluid = water Inlet diameter, D1 = 400 mm Outlet diameter, D2 = 300 mm The…

Q: Calculate the horizontal displacement of the C point in the system shown in the figure

A: Use Virtual Work Method (Unit Load Method) Consider the free body diagram of the given frame as…

Q: An open rectangular tank moves upward along a 30o-incline as shown in the figure. What is the slope…

A: Given diagram

Q: Compute for the density of the liquid in kg/m^3.

A: This question is from Fluid mechanics

Q: The velocity field for steady, incompressible, two-dimensional flow through a converging duct is:…

A: Given, Velocity, V = (U0 + bx)i - by  where, U0 and b are constants to determine streamline equation…

Q: Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

A:

Q: 5.2. Consider the situation of when two lanes of traffic merge down to one lane, as shown in Figure…

A: All conditions at any location in a stream stay constant with regard to time in a steady flow. A…

Q: For the configuration illustrated below, find the value of P in the active case. You may assume that…

A: To find value of P??

Q: A rectangular canal carrying 10 cubic meters per second of water is laid on a slope of 3m per km.…

A: Discharge is defined as the volume of water displaced per unit time (sec).  The discharge of the…

Q: A block is pushed against a horizontal spring, compressing it to 22 cm. After being released, the…

A:

Q: Dam has a face curved as shown. Determine the magnitude (in newton) and direction (in degree) of the…

A: Given data: Unit weight = 9810.4321 N/m^3 equation y = x^6 for the non-linear curve

Q: coefficient of friction is given by f = C friction for a length 10m of this pipe. "

A:

Q: A Sharp-edged orifice 10 cm in diameter, in the side of a tank having cross section 2 m square,…

A: Cd=0.67 d=10cm

Q: In the vertical plane, a 725 g block slides on a circular path with a radius of 3.15 m. If the block…

A: Given:- The mass of the block = 725 g = 0.725 kg The radius of the circular path = R = 3.15 m  The…

Q: head loss due to friction.

A: Given data, Diameter of a horizontal steel pipe,d= 100 mm=0.1 mf=0.0220Length,l= 400mVolumetric flow…

Q: A variable mesh screen produces a linear and axisymmetric velocity profile as indicated in the…

A: A variable mesh screen produces a linear and axisymmetric velocity profile for the airflowDiameter…

Q: The rectangular bin with an inclined gate AB is filled with oil to the depth shown. Determine the…

A: Determine resultant force acting on inclined side AB

Q: 5 A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible…

A:

Q: The rectangular canal shown in the figure below changes to a round pipe of diameter D as it passes…

A: Answer We can determine the Diameter 'D' in terms of 'b'  using continuity equation Q = A1*V1 =…