A pipe bends through (48)° from its initial direction as shown in Figure C. The diameter of the pipe gradually reduces such that diameter at inlet is 400 mm and outlet is 300 mm. At the inlet, the flowrate of water and pressure values are 0.053 m³/sec and 40 N/cm² respectively. Determine the following: 1) Velocities at inlet and outlet 2) Pressure at outlet 3) The total resultant force on the bend and its direction

A pipe bends through (48)° from its initial direction as shown in Figure C. The diameter of the pipe gradually reduces such that diameter at inlet is 400 mm and outlet is 300 mm. At the inlet, the flowrate of water and pressure values are 0.053 m³/sec and 40 N/cm² respectively. Determine the following: 1) Velocities at inlet and outlet 2) Pressure at outlet 3) The total resultant force on the bend and its direction

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3 feet -hinge AC Linseed Oil (SG = 0.938) Castor Oil 32 feet (SG = 0.96) 7 feet 1water B 77

Q: A 0.3 m diameter pipeline terminates nozzle of outlet diameter = 0.15 m. The free jet from the…

A: Dia of pipeline = 0.3 mOutlet diameter = 0.15 mDeflection of Jet = 90 degreeDischarge of water =…

Q: 50 cm Water m kg/s 2 50 cm FR. Water If another (identical) elbow is attached to the existing elbow…

Q: Q3/ Water flows through a pipe at 5 L/s, as shown in Fig. 12.5 kPa, 11.5 kPa, and 10.3 kPa are…

A: Given, P1 = 12.5 kPa P2 = 11.5 kPa P3 = 10.3 kPa Q = 5 L/s or 0.005 m3/s NOTE : As per guidelines,…

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

Q: neqaned mormation A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of…

A: Diameter of elbow=10cm = 0.1m Momentum flux correction factor=1.03

Q: Consider the gate shown in the figure. If the length of the gate is 5 meters, calculate: LS. r= 4m…

Q: concentrically with speed of 30 m/s. Calculate the force exerted on the plate if the jet issuing…

A: V1=V2=V=30m/s D=5cm d=2cm

Q: 3. A tank in figure C is accelerated to the right and the width of the tank is 1 m. Determine the…

Q: water flows at a rate of 0.5m/sec round a 50 contracting pipe bend which lies in a horizontal plane.…

Q: 1:43 ..l 57 Shown below is the curved section of:

Q: In the given figure, rectangular gates AB and CD are shown. If the width of both gates is 3m,…

Q: 8- Water flows through a horizontal reducing bend shown in Figure 3 below at an unknown bend angle,…

Q: 36 " chinge Linseed Oil А (SG = 0.938) Castor Oil 32 feet (SG = 0.96) 7 feet 11ater В

Q: m Water is flowing through a horizontal pipe of diameter 150mm at a velocity of 2-. A circular solid…

A: Given:Pipe diameter, D = 150 mm = 0.15 mVelocity of flow, V = 2 m/sDiameter of solid plate, d = 120…

Q: A horizontal pipe 30-cm in diameter bends through 135°. The velocity of flow of gasoline (SG = 0.8)…

Q: Question 02 A tapering pipe bend (in horizontal plane) is supported at point A and connected to a…

A: Given values, D1=75 mm D2=50 mm p1= 720 KN/m2 p2=476 KN/m2 h1= 250 mm h2= 300 mm Q = 0.045 m3/s

Q: through a 11.5-cm-diameter pipe that has a 180° vertical bend, as in the figure. The total length of…

Q: A pipe of 220mm diameter conveying a fluid of density 750 kg/m³ and conveying it with a flow rate of…

A: Given data in question 90 degree bend pipe Pressure at inlet and outlet Diameter Discharge…

Q: A water tank has a right-triangular panel near the bottom, as in Figure 2. Omitting Pa, find and…

A: Given: The value of h1 is 5 m. The value of h2 is 13 m. The angle is 40o. The value of a is 12 m.…

Q: a b A jet issues from the side of the tank under a head of a = 4.15 m. The orifice is positioned…

Q: In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) =…

Q: 1. Hydrostatic force on a curved surface Consider the container with the half-sphere dome, filled…

A: radius of sphere R = 1 m Height = 10 m

Q: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two…

Q: Q3 hydraulic jump, as in below figure. If yı=1 m and ys-40 cm, estimate a) V1, V3 b) the bump height…

Q: Q2. The rectangular AB gate whose width is 2.2 m shown in the following figure is hinged at point A.…

Q: water surface 2.5 m 2.7 m y2 = 5x (parabola) %3D

Q: Three pipes steadily deliver water at 20°C to a large exit pipe in Figure 1. The velocity V; = 5…

A: Given data, Q4 = 120 m³/s V2 = 5 m/s To find out the V1, V3 and V4

Q: ) Water flows in a rectangular channel of 5 m wide as shown in figure below. Calculate a) the force…

Q: Q34. A 10 cm diameter jet of water éxerts a force of 2 kN in the direction of flow against a…

Q: Q.5.b) Three pipes steadily deliver water at 20°C to a large exit pipe in Figure below. The velocity…

Q: Smooth pipe: d=50mm P1 1 10 m I 40m->> 20m 80 m Open jet

Q: Consider a fully developed laminar flow of a fluid through a 8027 m long and 4 cm diamete horizontal…

A: length, l = 8027m diameter, d = 4 cm Pressure, P= 1252 kg/m3 i) Velocity profile given, U = 61-rR2…

Q: 100 AN Frictirness pin 75 KNin 55 LNin 25m Im 15m 3m

A: Considering the vertical reaction: ∑V=0RA+RE+RC=75×5+100+55×3RA+RE+RC=640

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

A pipe bends through (48)° from its initial direction as shown in Figure C. The diameter of the pipe
gradually reduces such that diameter at inlet is 400 mm and outlet is 300 mm. At the inlet, the
flowrate of water and pressure values are 0.053 m³/sec and 40 N/cm² respectively. Determine
the following:
1) Velocities at inlet and outlet
2) Pressure at outlet
3) The total resultant force on the bend and its direction
Flow
direction
Figure C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction and given data

VIEW

Step 2 Velocity at the inlet and the outlet

VIEW

Step 3 Pressure at the outlet

VIEW

Step 4 Resultant force at the bend and the direction

VIEW

Step 5 Final answer

VIEW

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The laminar flow takes place between closely spaced parallel plates as shown in figure below. u > V y Ľ The velocity profile is given by u = v. The gap height h is 5 mm and the space is filled with oil (specific gravity = 0.86, viscosity μ = 2 x 10-4 N-s/m²). The bottom plate is stationary and the top plate moves with a steady velocity of v= 5cm/s. The area of the plate is 0.25 m². The rate of rotation of a fluid particles is given by
A 60° bend occurs in a water pipeline that reduces from 600 mm diameter to 300 mm diameter at the bend (inside bend angle 120). If the gauge pressure at the inlet is 172 KPa, determine the magnitude ad angle of the thrust on the bend when the flow is 0.85 m/s. Hint: start by calculating the initial and final velocities, then the final pressure. Next, analyze the pressure and momentum forces in the x and y planes.
In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) = 40 m/s, velocity of flow at the outlet of the pipe (V2) = 20 m/s and the acceleration due to gravity is assumed to be 10 m/s2, then the loss of head due to sudden enlargement of pipe is: a. 18 m of water b. 40 m of water c. 15 m of water d. 20 m of water
H.W. 6.32 Q: in a (45°) bend a rectangular air duct of (1) m² cross-sectional area is gradually reduced to (0.5) m² area. Find the magnitude and direction of the force required to hold the duct in position if the velocity of flow at (1) m² section is (10) m/s and pressure is (2.943) N/cm². Take density of air as (1.16) kg/m³. 66
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 47 kg/s. Another identical elbow is attached to the existing elbow such that the water flow makes a U-turn as shown in the second figure. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Take the density of water to be 1000 kg/m³. Water m kg/s Water 2 1 FRI 50 cm FRX 50 cm If another (identical) elbow is attached to the existing elbow so that the fluid makes a U-turn, determine the magnitude of anchoring force needed to hold the elbow in place. The magnitude of anchoring force needed to hold the elbow in place is 438 * N.
Note:hand written solution should be avoided.
A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 43 kg/s. Another identical elbow is attached to the existing elbow such that the water flow makes a U-turn as shown in the second figure. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Take the density of water to be 1000 kg/m3.
Imagine that the water level in Problem 8.34 rises at a rate of 0.1 cm/s. Knowing the diameter of the tank is 15 cm, what is the average velocity of the water leaving the tank?
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. a. The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c. The hydrostatic force due to water. d. The net hydrostatic force acting on the gate Fnet
Problem 6.25 , show step by step solution
Problem 3: Shipping Tool is moving.. M1 = 5.5 1 (2) 8₂ = 12° Air at Mach, M1 = 5.5 at a pressure of P1 = 70 kpa flows along a smooth curved wall bending away at an angle of 12°. Determine the Mach number, temperature, density, velocity, speed of sound and pressure, total pressure, and total temperature after the bend in region-2. M₂