Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine. The dimensions and values are given. One of the steps is not required to find the required length of the HX, if the oil leaves at 60 C? Oil and water inlet temperatures are 100 and 30 C, respectively. Thermal entry length to validate the steps O None of the above Log mean temperature difference Reynolds number, Prandtl number and Nusselt number O Overall heat transfer coefficient

Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine. The dimensions and values are given. One of the steps is not required to find the required length of the HX, if the oil leaves at 60 C? Oil and water inlet temperatures are 100 and 30 C, respectively. Thermal entry length to validate the steps O None of the above Log mean temperature difference Reynolds number, Prandtl number and Nusselt number O Overall heat transfer coefficient

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sat wr oted 120.3°c through steel Yepor Flows Pipe (上 = 25 3K) steel hos diometer The Pipe inside 52 5 33i outside dione ter 58.5 ond length 30m The Surf a ce of in suloti^g Pipe is cooted w.th moteria( which hos of thick ness 25 mm(k=0,25 wimk k 0, 25 w/mk) The ambien + temper ture is 27°C Find the amount of heat los8 and of woter Con den sates in = 2705 6 ヒ1kgk Pipe Hvopor Saturoted water =505.4 Wikgk SHOT ON MI6 MI DUAL CAMERA
For the given temperature profile diagram for a heat exchanger, which of the following equation is coIrect, ping x Boding fhed Inlet Outiet a. mhyg = m.Cpc(Tco – Tei) b. m.Cpn(Tn - Tho) = m.Cpc(Ta – Teco) m,C,(Th: - Tho) = m.Cpc(Tco – Te) m,Cpn (Thi - Tho) = m.hr,
heat trawafer coefficient Problem #21. Cz Moo Cethanal) i (flow pute - 12.4 mh) through a being 98.6°F heate d from m2/h) though a 2-4 Shell and tube heat exchong er whing hot water (flow pate= 8-29 m³ /h, 155.39 °F). inlet temperature- 221 F, outlet mperature= awerage heat capaci ty of CaHeO - li63 Btu J lb'F = 5.8 * 105 Watts = 363. 99 Btu|hft°F heat trans fer rate ethanol %3D overall heat trawafer %3D Jelve for: a. comeetion factor 6 (Ao) mean temperature differe nce outaide nur face are a veguired
Handwritten -HT
PLZ I want full answer with all solution steps A heat exchanger is to be designed to heat 32/68 mixture of ethylene glycol and water from 24 °C to 55 °C by a hot water stream from 79 °C to 42 °C. Flow rate of cold stream is 20 kg/s. Inlet pressure for both stream is 50 psi and the maximum pressure drop of 10 psi for cold stream and 8 psi for hot water are permissible. Report valid assumptions made for the design and give required justification. Estimate i) Heat Transfer, Corrected LMTD, ii) Tube bundle diameter (Using TEMA standards and Codes) and Tube cross sectional area iii) Heat transfer coefficient iv) Overall heat transfer coefficient v) Pressure Drop (Shell side & Tube Side) note: Assume any values for the missing data
Question about heat exchanger
HEAT TRANSFER 4 decimal places. Thank you
The meaning of the efficiency coefficient for a heat exchanger and the effects of the efficiency coefficient Briefly write the parameters
Prlen # 9. Solve for: a) heat tranefer pate of ayatem ) mass Mow rate bath Atreams. Ueing a double kipe Reat eschunger (imside di anaeten =0.38 m, %3D outside diaetu = 0.40 m total length= 0.14 m steam (0.12 mPa kas wndengme The steam conde na atiin method. wtili ged peservoir water flow, outlet ald fluid temp. = at 306.95 K using 321.85 K countereurrent Uaing ouerall neat tranefer outride Aurface area, Crefficint: Uo-5219.97 W/m² K
10. Recall when you were collecting data for the Entrance Loss experiment, there was a ten second delay before the data was posted in Excel. Why was there a delay, and why was it important? 11. Were your theoretical entrance loss factors, KL, higher or lower than your experimental value? What may be some causes for each entrance type? Concentric Tube Heat Exchanger 12. Why was it difficult to achieve steady-state conditions? 13. List at least two assumptions that are being made in the Heat Exchanger experiment, and explain the reasons why they are approximations. 14. What are thermal and hydrodynamic entrance lengths? Are either (or both) of them an issue for the experiment? Why or why not?
The chief engineer at a university that is constructing a large number of new student dormitories decides to install a counter flow concentric tube heat exchanger on each of the dormitory shower drains. The thin walled copper drains are of diameter Di = 50 mm. Wastewater from the shower enters the heat exchanger at Th,i= 38°C while fresh water enters the dormitory at Tc,i= 10° The wastewater flows down the vertical wall of the drain in a thin, falling fil , providing hh = 10,000 W/m2. K.If the annular gap is d= 10 mm, the heat exchanger length is L= 1 m, and the water flow rate is m˙ =10 kg/min, determine the heat transfer rate and the outlet temperature of the warmed fresh water.If a helical spring is installed in the annular gap so the fresh water is forced to follow a spiral path from the inlet to the fresh water outlet, resulting in hc = 9050 W/m2.K, determine the heat transfer rate and the outlet temperature of the fresh water.Based on the result for part (b), calculate the daily…
Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810 J/kg. °C) from 66 °C to 39 °C.Water (Cp = 4200 J/kg. °C) at 10 °C is pumped at 4750 kg/h to cool the solution. The tube side fluid flows in a circular pipe with an outside diameter of 25 mm. The overall heat transfer coefficient is (6.84x10^2) W/(m².°C). Find the tube length 'L' for one pass of a two-pass parallel flow double-pipe heat exchanger as shown in Figure. Answer should be in m with three significant figures.