concentrated load that this beam can carry besides its own weight. Use fc = 7MPA, fs = 124 MPa, n = 1 400 -25

Q: Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel…

A: Given :

Q: Classify the structure as statically determinate (Write SD), statically indeterminate (Write only…

A: Ds=3m+r-3j m=number of members r=external support reaction j=number of joints

Q: For the frame shown in Figure AN-17, using the Moment Distribution Method: NOTE: If I is not…

A:

Q: Prove that: Y = (Gs+ eS;' Yw 1+e

A:

Q: Solve the ff. Exact de

A: Please see the attached images for the solution.  If there are queries or if the images are not…

Q: following differentiable function of x and y:

A:

Q: Determine (a) the x, y, and z components of the 750-N force, (b) the angles 0,, 0, and 0, that the…

A: first, draw the vertical and horizontal components Then calculate the scalar components The force…

Q: Determine (a) the x. y, and z components of the 750-N force, (b) the angles , and e, that the force…

A: a) Fx=750 cos55° cos25° =389.88 N          ( Hint : Resolving 750 N to xz plane and resolving to…

Q: Draw M, N, T diagrams using the cutting method.

A:

Q: Apply Castigliano's 2nd theorem # EA EA 0.5EP CA EA 3m x 3m. (A) + + X dyA

A:

Q: 136 N is the asnwer in the

A:

Q: Compute y. (16 – 2 x 2.5) = 0.69 16

A: Given: γ=16-2×2.516

Q: Convert the following and round off to nearest hundredth if necessary. 10ft³ to cm³

A:

Q: 8 sin x cos x = sec?x. Prove sin 4x + 2sin 2x

A:

Q: The pump in the figure discharges water at 45 lit/s. Neglecting losses and elevation changes, 3.…

A: Apply Bernoullis theorem…

Q: Flow and spacing are inversely related O True O False

A: State true or false Flow and spacing are inversely related

Q: as pule a5 pyle PL 6x1 6 pulg 2<3x3x1/2 15 pulg I pule -3 pulg-3 pulg Angular 3x3x:A=2.75 in :j =…

A: For any compound section to find the centroid we divide that compound section into basic elements…

Q: A circular stepped steel shaft has the dimensions and cross sections as shown in Figure Q1. It i…

A:

Q: Problem 10.6 - Locate the centroid of the section and determine the moment of inertia of the beam…

A:

Q: 4/Find fog(1) fCx)=x²-1 3(カー×3

A:

Q: Find ØMn for the beams of cross section shown. Assume physical dimension are acceptable. 760 fc' -…

A: As per mentioned in question,  effective cover of tension reinforcement  and bottom width are…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Assume c = 6, a = 1.15, b =…

A:

Q: | Question 1) Dimension the cross section of the rectangular cross section cantilever bar given ww…

A: From the given date and diagram it is required to find the beam cross section dimension i.e b &amp;…

Q: 10 GN/m² to kip/inch²

A: Given unit is GN/m2 1GN=224808.94kip And 1m=39.37inch

Q: Express e ach of the forces in Cartesian vector form etermine the magnitude and coordinate direction…

A:

Q: FH on the curved gate. Is S Water 4m -- -? If the gate width= 6 m F r=1my B 264600 NO 264600 lb O…

A:

Q: Particular solution of (D³ + 12 D² + 36 D)y = 0, %3D

A: Differential equation: - It is defined as a mathematical equation which is useful to relate one or…

Q: Determine the location of the centroid of the area.  Segments A,B, and C. I can't figure how to find…

A: Centroid will be at ( 2.5 , 4 ) from lower left cornerExplanation:

Q: If a=100 inch, b=52 inch and C=60 degrees find c

A: To determine the third side (c) of a triangle provided we have, the other two sides (a and b) and…

Q: Compute for the location of the point C (x, and yo). which is the centroid of the section reckoned…

A:

Q: Use the area method. The two beams shown are connected by an internal hinge at C and are supported…

A:

Q: Given. d₁=20cm or d₂ 20cm or C = 0·80 For Rectangular port, t₁ = "S" Adh ₂ 21h 1-8 3 4₁ = 2021-125/1…

A:

Q: Problem II. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What…

A:

Q: Determine: a) Location of the centroid of the triangle   *use 3 decimal places

A:

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

A:

Q: Solve the following equations 64. y" + 3y - 28y = 10e Ax

A:

Q: RI 038 R32 80

A: For the given figure, i had drawned in AUTO-CAD using the following commands 1. CIRCLE COMMAND 2.…

Q: PROCEDURE 4 center of gravity 10cm 20cn G8.2cm 50cm 100 cm 10g 20g Cog FBD dz di f W F2 mg:10g FI…

A: Given FBD

Q: A being Write a mass is located i Determine lifting used of 800kg. in the The Ас and 11) Determine…

A: Mass of the steel beam = 800 kgCG of the steel beam is at the center of the span.It is asked to…

Q: The symmetrical two-pinned arch shown in Fig. P.16.22 comprises two segments each having a radius of…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.