Compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 28000 kPa and 35000 kPa, respectively. The diameters are 6.35 mm for the pin, and 12.7 mm for the control rod. Assume single shear for the pin at B.

Compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 28000 kPa and 35000 kPa, respectively. The diameters are 6.35 mm for the pin, and 12.7 mm for the control rod. Assume single shear for the pin at B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution with clear calculations
#2 handwritten then box the final answers
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
1. A solid steel shaft 3in in diameter and 4ft long is fixed at one end and free at the other, as shown. The shaft is subjected to an axial tensile load of 50,000 lbs. a. Compute the magnitude of the force P at the free end necessary to reduce the stress at point B to zero. b. Compute the maximum combined stress at point A. 50.000 b 4'-0"
Problem 2 Knowing that each of the shafts AB, BC, and CD below consist of a solid circular rod, determine the maximum shear stress in each shaft. 60 N - m 144 N. m. D 48 N- m dcp= 21 mm %3D C dBc = 18 mm B dAB = 15 mm A %3D
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
make it understanda
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
A compound shaft made of steel and aluminium transmits 75 kW at 900 rpm. Determine the maximum shear stress and relative angle of twist between surfaces at two extreme ends located at A and C. Neglect any strain concentration effect. Esteel = 207 GPa, EA1 = 73 GPa, VAI = 0.334, and Vsteel = 0.33. F Aluminium 60 800- B Steel 75 1000 All dimensions are in mm
PROVIDE A CLEAR SOLUTION AND THE RIGHT ANSWER FOR THIS PROBLEM. PROVIDE INDIVIDUAL FBD
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
6. Referring to Figure 6, compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 4000 psi and 5000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the control rod. Assume single shear for the pin at B. 2 in 6 in FIGURE 6 BC 2 in 10° T