Compute the final velocities v₁' and v₂' after collision of the two cylinders which slide on the smooth horizontal shaft. The velocities are positive if to the right, negative if to the left. The coefficient of restitution is e = 0.83. Assime v₁ = 27 ft/sec, v2= 4 ft/sec, W₁ = 6 lb, W₂ = 16 lb. V1 V2 Answers: W₁ W2 V₁' = i ft/sec V2' = = ft/sec

Compute the final velocities v₁' and v₂' after collision of the two cylinders which slide on the smooth horizontal shaft. The velocities are positive if to the right, negative if to the left. The coefficient of restitution is e = 0.83. Assime v₁ = 27 ft/sec, v2= 4 ft/sec, W₁ = 6 lb, W₂ = 16 lb. V1 V2 Answers: W₁ W2 V₁' = i ft/sec V2' = = ft/sec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid 3
The system is released from rest in the configuration shown at time t = 0. Determine the time t when the block of mass m, contacts the lower stop of the body of mass m2. Also, determine the corresponding distance s2 traveled by m2. Use the values m, = 0.8 kg, m2 = 2.9 kg, P; = 0.29, Hk = 0.23, and d = 0.38 m. m1 m2 smooth- 23° Part 1 Find the magnitude of the acceleration of each mass. Answers: a1 = m/s? a2 = m/s2
A piston is used to support a load of 90kN. The hydraulic oil used has a specific gravity of 0.81. If the pressure below the piston is 1.33MPA. Obtain the diameter of piston in mm. a. 294 b. 258 C. 463 d. 327
Fluid flows at a velocity V through a horizontal pipe of diameter D. An orifice plate containing a hole of diameter d is placed in the pipe. It is desired to investigate the pressure drop, 4p, across the plate. Assume that Ap f(D, d, p, V) where p is the fluid density. Determine all possible z terms. Show ALL steps. (Figure shows a longitudinal profile section of the pipe). Use FLT Svstem ONLY P1|| P2 Flow
4
The 0.5-kg cylinder A is released from rest from the position shown and drops the distance h, It then collides with the 0.4-kg block B; the coeffi- cient of restitution is e = 0.8. Determine the maxi- downward displacement h2 of block B. Neglect all friction and assume that block B is ini- tially held in place by a hidden mechanism until the collision begins. The two springs of modulus 400 N/m are initially unstretched, and the dis- 0.8 m. || mum k = |3| tance d 1.0 m. %3D MA A. ITB www he
Solve with the use of a free body diagram (Complete FBD required)
A 6.2-liter HEMI V8 Hellcat Redeye engine that weighs 875 lbs is being lifted by a portable floor crane. In the position shown, compute the magnitude of the force supported by the pin at C with complete FBD and the oil pressure p against the 3.20-inch diameter piston of the hydraulic-cylinder unit AB. (Pressure = Force/Area).
30
Use 3 decimal places in your solution
Solve for R,d,Ray,Rby,Rbx
Determine the maximum deflection of the solid circular shaft illustrated in Figure 3. The shaft is made of steel having Young's modulus E-210 GPa and a diameter d - 80 mm. 10 kN 5 kN-m 5 kN-m CY -X- 1.5 m Figure 3 1.5 m B