Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal stress in member AD, if a force P of magnitude 300 N is applied to the handles of the bolt cutter shown in figure below, from which it has a uniform cross-sectional area of 2x10-4 m22x10-4 m². 300 N 24 mm 12 mm B 96 mm 24 mm 24 mm - 460 mm 300 N

Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal stress in member AD, if a force P of magnitude 300 N is applied to the handles of the bolt cutter shown in figure below, from which it has a uniform cross-sectional area of 2x10-4 m22x10-4 m². 300 N 24 mm 12 mm B 96 mm 24 mm 24 mm - 460 mm 300 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-41.M A shelf is being designed to hold crates having a to- tal mass of 1840 kg. Two support rods like those shown in Figure P1-41 hold the shelf. Each rod has a diameter of 12.0 mm. Assume that the center of grav- ity of the crates is at the middle of the shelf. Compute the stress in the middle portion of the rods. 1840 kg -600 mm Support rods (2) 30% 1200 mm Shelf
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. A parameter value units 470 mm 400 mm 40 mm 30 mm 30 KN cc 080 BY NO SA 2021 Cathy Zupke L₁ L2 d₁ d₂ P 4₁ B C E The stress in AB σAB= The stress in CD and EF: OCD = EF= d₂ L₂ MPa D F MPa
3. Four pulleys are attached to the 50-mm-diameter aluminum shaft. If torques are applied to the pulleys as shown in the figure, determine the maximum shear stress in each segment and the angle of rotation of pulley D relative to pulley A. Use G = 28 GPa for aluminum. a. Tab= b. Tbc= C. Tbc= ad= 1100 N·m 800 N·m D C 900 N·m 600 N m B A 2 m3 m2 m
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. For the connection shown, the average shear stress in the 13-mm-diameter bolts must be limited to 270 MPa. Determine the maximum load P that may be applied to the connection. O 271 KN O 215 kN O 232 KN O 291 KN O 173 kN
The block of weight W in the figure below hangs from the pin at A. The bars AB and AC are pinned to the support at B and C. The areas are 800 mm2 for AB and 400 mm2 for AC. Neglecting the weight of the bars, determine the maximum safe value of W if the stress in AB is limited to 110 MPa and the in AC to 120 MPa.
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in the square after the pressure is applied is as shown in the figure. Determine the change in length of the BC edge in (mm).
If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will require the link to have a minimum thickness of: 30 mm 10 mm 3.20 mm 2.60 mm 2.40 mm 2.20 mm 3.60 mm 3.00 mm 2.80 mm O 3.40 mm
Part A The bolted connection (Figure 1) joins the bar supporting force P to two flanges set into a wall at A and B. In addition to supporting the load transferred by the bolt, the flanges are also subjected to additional 5-kN and 2-kN loads, as shown. Determine the largest internal shear force resisted by the bolt when P= 8 kN. (Figure 1) Express your answer to three significant figures and include appropriate units. Value Units Submit Request Answer Part B Determine the largest internal shear force resisted by the bolt when P = 23 kN and P = 18.6 kN. (Figure 2) Express your answer to three significant figures and include appropriate units. Value Units Figure Submit Request Answer SAN Provide Feedback Next > 2kN
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
Q2/ for the system shown in figure find the shear stress in the bolts in (A) and (B) knowing that the bolt diameter is 20mm 10KN/m Im 4m 1m
Assemble a pair of parts A and B with serrated teeth as shown in the figure on the right.A compressive load of 24 kN is acting on the combined structure.The compressive load is transmitted by the three meshing teethTo. Shear stress and compressive stress (contact) generated in the tooth at this timeFind each tactile stress.