compare the load required to produce equal depression for two beams made of the same material and having same length and weight with only difference that one has circular cross-section while the cross-section of other is square.

Q: Assume a leg has 0.06 m shaft of bone with an average cross sectional area of 2.5 m2 , What is the…

A: Young's Modulus of a material is the measure of it's elasticity, and it is equal to the ratio of the…

Q: steel beam of uniform cross section weighs 2.50 x 10^5 N. if it is 5.00m long. what force is…

A:

Q: 21 A firefighter weighs 730 NL She owears shoes that each cover an atea of 309 am. (a) Wihat is tthe…

A: Weight of the person F=730 N Area covered by the single shoe A1=309cm2=0.0309 m2

Q: (h) What is the difference between engineering stress and true stress?

A: True stress is the applied load divided by the actual cross-sectional area (the changing area with…

Q: Read the following two statements below carefully and state, with reasons, if it is true or…

A: (a)False.

Q: Assume a leg has 0.6 m shaft of bone with an average cross sectional area of 1.5 cm² , What is the…

A:

Q: (iii) Draw a stress-strain graph for a ductile material illustrating elastic and plastic behaviour.…

A: Ductile material is a material that can be easily converted into sheets or wire when force is…

Q: Determine the absolute maximum value of shear produced by the wheel loads in a simply supported beam…

A:

Q: Tensile stress is the same as force V applied force per cross-sectional area the strain per unit…

A: Tensile stress is force per unit area. tensile stress=applied forcecross sectional area stress has…

Q: T the stress experience when deformation is caused by tangential forces to the surface* O Inertia…

A:

Q: A body of mass 500 kg is suspended at the free end of an iron wire of length 3 m and cross-sectional…

A:

Q: Under certain loading conditions, can a Truss ever include a two-force member that experiences zero…

A: Answer:   Introduction:   It is here to introduce that under certain loading conditions, Truss ever…

Q: One end of a wire 2 m long and 0-2 cm' in cross-section is fixed in a ceiling and a load of 4:8 kg…

A:

Q: As an oil well is drilled, each new section of drill pipe supports its own weight and that of the…

A: the total weight of the pipe is F=weight of the pipe+weight of the drill bit=m'L0+l+mg=23kg/m3000…

Q: A sculpture weighing 75,757.5 N rests on a horizontal surface at the top of a 7.5-m-tall vertical…

A:

Q: Simply supported beam ABCD is subjected to uniformly distributed load has a span length of 10m. The…

A: please see the next step for solution

Q: What shear stress is needed to produce a shear strain of 2.50 x 10-5 on an aluminum block?

A: shear modulus=shear stressshear strainshear stress=shear modulusshear strain

Q: capacity of the soil is 170 kNm uming the following material s

A: Given as, Dead Load Gk = 1105 KN Live load Qk = 260 KN Column Load Dead Load Gk = 1050 KN Live load…

Q: (d) One end of an iron rod with a diameter of 1.6 cm and a length of 0.7 m is held in a vise. A…

A: (d) In this case, the iron rod having some length and some diameter. Then a force is applied…

Q: 206. A steel wire 10m long hanging vertically supports a tensile load of 2000N. Neglecting the…

A: The diameter of the wire can be calculated by using the formula  L=EπD2∆L4FD =4FLEπ∆LWhere, A is a…

Q: 41-50. The homogeneous bar is supported by a smooth pin at Cand a cable that runs from A to B around…

A: Given: The diameter is 0.6 inch. The weight of the bar is 5000 lb.

Q: How stress and strain distribute in an elastic body when load is applied on its cross sectional…

A: It is as per Hook's law Stress is proportional to strain. for small deformation

Q: In the figure 20.0 kg boom of length 4.00 m is supported by a cable that has a breaking tension of…

A:

Q: A uniform 30-lb beam, 10 feet long is carried by two mean A and B, one at each end of the beam. a)…

A: Given that Force exerted by man A(F1) =25lb and length of the beam (L)=10feet and weight of the load…

Q: A short timber post of rectangular section has one side twice the other. It contracts by 0.05 cm/m.…

A: Given data: The contraction in timber is ΔL/L=0.05 cm/m. The axial load is F=10 kN. The Young's…

Q: "One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of…

A:

Q: ne turnbuckie cames an axia ad, what maximum load ess is limited to 180 MN/m2 ICKI [39

A: As per rule, allowed to answer first question and post the remaining in the next submission.   Given…

Q: Example 2: Assume a leg has 0.6 m shaft of bone with an average cross sectional area of 1.5 cm²,…

A: Given data, Length l=0.6 m. Cross sectional area A=1.5 cm2=1.5×10-4 m2. Force is given F=350 N.…

Q: An elastic with the elasticity constant of 20 N/m, and mass of 4 kg, is fastened to the ceiling and…

A:

Q: A homogeneous 800 kg bar AB is supported at either end by a cable Bronze Steel show. Calculate the…

A:

Q: In the clevis shown, find the minimum bolt diameter  that will support a load P = 14 kips without…

A: Given Data:- The load is P = 14 kips. The shearing stress is τ =14 ksi. The bearing stress is σB =…

Q: C On the figure shown above is a rod supported by a rope, if the length of rod and rope is 1 m and…

A: In this question we have to find the value of h. Please give positive feedback if the answer helps…