capacity of the soil is 170 kNm uming the following material s
Q: Assume the breaking stress of a bone is 1.30 x 107 N/m2, the magnitude of the maximum force a…
A: Given Breaking stress of a bone =1.30x107Nm2 Average diameter of bone =d= 3cm Area of bone=πd24…
Q: The maximum stress that a material can endure before it breaks is called Ultimate tensile strength O…
A:
Q: Assume a leg has 0.06 m shaft of bone with an average cross sectional area of 2.5 m2 , What is the…
A: Young's Modulus of a material is the measure of it's elasticity, and it is equal to the ratio of the…
Q: A rod with a radius of 0.005 m and length of 2 m stretches 0.002 m when subjected to a tension force…
A:
Q: A very important load on a structure is the pressure load. This loading is simplified for…
A:
Q: How much force would it take to break an aluminum wire that has a diameter of 0.22 cm?
A: The diameter of aluminum wire is given as d=0.22 cm
Q: A nylon rope used by mountaineers elongates 1.8 m under the weight of a 68-kg climber. If the rope…
A:
Q: In a zoo, a Metal-A cable with initial length of 4 meters and initial diameter 1 cm is needed to…
A: i) Elephant mass, M=1350 Kg initial Length of the rope, li=4 mInitial Diameter of the rope, di=1…
Q: An octopus uses one sucker of diameter 2.86 cm on each of the two shells of a clam in an attempt to…
A:
Q: The bar ABCD is fixed at A by a pin and supported by two wires as shown in fig. the bar is subjected…
A: The given figure is The figure for calculation be, Let us consider the two-similar triangles,…
Q: What happens when the stress applied to the body is increased beyond the maximum value and is…
A:
Q: (TUATION 3: A vertical brass post is 3.75m long and has a diameter of 25 cm. If the brass post is to…
A:
Q: (h) What is the difference between engineering stress and true stress?
A: True stress is the applied load divided by the actual cross-sectional area (the changing area with…
Q: Stiller Düzenleme Üs B 2) A uniform brass plate with area of 18 x 18 m? has mass of 41 kg which is…
A:
Q: Assume a leg has 0.6 m shaft of bone with an average cross sectional area of 1.5 cm² , What is the…
A:
Q: A vertical off-shore structure is built to withstand a maximum stress of 109 Pa. Is the structure…
A: Given : The maximum stress the structure can handle, P = 109 PaDepth of the sea, d = 3 km = 3 × 103…
Q: Determine the absolute maximum value of shear produced by the wheel loads in a simply supported beam…
A:
Q: How should we apply a force on a body to produce shearing stress?
A: Shear stress is the component of stress coplanar with the material cross section. It arises from the…
Q: Tensile stress is the same as force V applied force per cross-sectional area the strain per unit…
A: Tensile stress is force per unit area. tensile stress=applied forcecross sectional area stress has…
Q: Calculate the force a piano tuner applies to stretch a steel piano wire by 8.00 mm, if the wire is…
A: The cross-sectional area of the wire can be obtained as
Q: T the stress experience when deformation is caused by tangential forces to the surface* O Inertia…
A:
Q: Calculate the force a piano tuner applies to stretch a steel piano wire 10.00 mm, if the wire is…
A:
Q: Steel is more elastic than rubber. Explain.
A: Elasticity is the ability of a material to regain its shape once the deforming force is removed.
Q: A) by how much does a 55.3kg mountain climber stretch her 0.890 cm diameter nylon r ope when she…
A:
Q: A body of mass 500 kg is suspended at the free end of an iron wire of length 3 m and cross-sectional…
A:
Q: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to…
A: Given that the boom of the wall crane 4m long is held at right angles to the wall by a wire that is…
Q: A 17.0-m-high and 11.0-m-long wall and its bracing under construction are shown in the figure.…
A: The expression for the Torque due to wind force will be,
Q: a principle of physics states that for a relatively small deformation of an object, the displacement…
A: Deformation : Deformation is the change in the configuration of a a rigid object in response to the…
Q: One end of a wire 2 m long and 0-2 cm' in cross-section is fixed in a ceiling and a load of 4:8 kg…
A:
Q: A metal slab is on top of a concrete column which has a height of 6.5 meters and a diameter of 1.50…
A:
Q: n such a way that the volume increases by 0.3% (that is, AV/Vo = 3 x 10-3) relative to the space…
A: We know that the A moonshiner makes the error of filling a glass jar to the brim and capping it…
Q: Determine the load in member AB of the pin-connected truss 3m 3m 1 m 4 m 2m A 81 B 15 68 KN E www
A: given the load in member AB of the pin-connected truss is
Q: What would be the greatest length of a steel wire which when fixed at one end can hang freely…
A: Here we have to find the greatest length of the wire (l) in the question breaking stress is the…
Q: Q. 30 : What should be the weight suspended from the end of a steel wire 2m in length and by 2mm in…
A: Given-D=2mmTherefore-r=1 mm=0.001 mL=2ml=1 mm=0.001 m
Q: Can a wall exert a normal force? In what direction would it act?
A: The normal force is the amount of the which is applied by the surface when two objects come in…
Q: The owner of a company that manufactures drinking cups decides it would be impressive to build an…
A: By condition,
Q: The owner of a company that manufactures drinking cups decides it would be impressive to build an…
A: Area of the circular opening at the top is 1.44 times the area of the circular bottom. Depth of…
Q: The owner of a company that manufactures drinking cups decides it would be impressive to build an…
A:
Q: The tension is gradually increased from zero to a maximum value, and then reduced back to zero. 1.2…
A: Given : Length of copper wire = 1.2 m Cross sectional area of wire = 1.5 x 103m2. Also, The…
Q: The stress experienced by a certain surface is 17612Pa when a 17-N force is applied to it. How much…
A:
Designing and detailing of Square Pad footing - BS Code
(BS 8110 - 1997)
Step by step
Solved in 3 steps with 4 images
