Column A Column B ----------- is thus one consideration in the choice of instrument for a particular application. 1)- A- Sensitivity. B- Wear 2)- when the same input is applied repetitively over a short period of time. -- describes the closeness of output readings C- Accuracy D- Repeatability. 3) The accuracy of some instruments is sometimes quoted as E- Tolerance. a--------------? F- Linearity. 4) Careful instrument design is the most useful weapon in the battle against environmental inputs; by reducing the ---------of

Column A Column B ----------- is thus one consideration in the choice of instrument for a particular application. 1)- A- Sensitivity. B- Wear 2)- when the same input is applied repetitively over a short period of time. -- describes the closeness of output readings C- Accuracy D- Repeatability. 3) The accuracy of some instruments is sometimes quoted as E- Tolerance. a--------------? F- Linearity. 4) Careful instrument design is the most useful weapon in the battle against environmental inputs; by reducing the ---------of

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

Identify the given statement. FM and PM demodulators can actually reduce noise and increase the signal-to-noise ratio during the demodulation process by using limiters. This is known as the capture effect. Select your answer. The statement has no fixed information. The statement is false. The statement is true. The statement is a case-to-case basis.
I need the answer as soon as possible
B- An rate. analog signal having single frequency as 3 kHz is sampled with 5 kHz S Describe its frequency spectrum. What will be the output if the sampled signals a passed through a low-pass filter having cutoff frequency at 2.5 kHz? signal. are sent in the analog
1
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
4. Line Regulation is determined by: a. Load current b. Changes in the load resistance and output voltage C. Changes in output and input voltage below deta
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
An analog signal having a maximum frequency of 40 Hz is sampled with a sampling rate of 20 Hz. What will be the value of the digital frequency?
Calculate the output impedance for small-signal equivalent circuit. (R=10 k2, r. =10 k2) ER Rout O A) Rout = 3.3 ka O B) Rout = 20 ko )C) Rout = 30 ka DI Rout = 5 k0
VI Ru Ri Vz I, Io R2 = 3837.79 O. R3 = 3989.3 Q. %3D R4 = 2898.06 Q. V1 = 4.8 V. V2 = 8.1 V. 11 = 0.0099 A Determine the following: a.) The output current lo %3D
Signal-to-Noise ratio is calculated as:Select the correct response:A. signal voltage divided by noise voltageB. signal power divided by noise powerC. first add the signal power to the noise power, then divide by noise powerD. none of the above
please answer all thanks !