Cold water entering an opposing flow heat exchanger at a flow rate of 0.6 kg/s at 20 oC (cp =4180 J/kg.K) with a flow rate of 0.75 kg/s of oil (cp = 2200 J/kg.K) it is used for cooling from 110 OC to 85 oC. If the total heat transfer coefficient is 800 W / m2.lf K, What is the heat transfer area of the heat exchanger? %3D

Cold water entering an opposing flow heat exchanger at a flow rate of 0.6 kg/s at 20 oC (cp =4180 J/kg.K) with a flow rate of 0.75 kg/s of oil (cp = 2200 J/kg.K) it is used for cooling from 110 OC to 85 oC. If the total heat transfer coefficient is 800 W / m2.lf K, What is the heat transfer area of the heat exchanger? %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
IP Heat Transport in the Human Body The core temperature of the human body is 37.0 ∘C∘C, and the skin, with a surface area of 1.40 m2m2, has a temperature of 34.0 ∘C∘C. Find the rate of heat transfer out of the body under the following assumptions: (i) The average thickness of tissue between the core and the skin is 1.20 cmcm; (ii) the thermal conductivity of the tissue is that of water. Express your answer using two significant figures. Without repeating the calculation of part A, what rate of heat transfer would you expect if the skin temperature were to fall to 31.0 ∘C∘C? Express your answer using two significant figures.
The overall heat transfer coefficient in internal combustion engine depend on Select one: O a. Only on the Prandtl number O b. On The Reynolds number O c. On the temperature of the intake air d. On the area of heat transfer
A heat exchanger has an over-all coefficient of heat transfer of 900 W/m2-K. The mean temperature difference is 20C and heat loss is 15,000 W. Calculate the heat transfer area. Group of answer choices 0.765 ?2 0.557 ?2 0.833 ?2 0.712 ?2
5. Hot exhaust gases, which enter a finned-tube, cross-flow heat exchanger at 300 °C and leave at 100 °C, are used to heat pressurized water at a flow rate of 1 kg/s from 35 °C 125 °C. The specific heat of water at the average water temperature is 4197 J/kg. K. The overall heat transfer coefficient based on the gas-side surface area is U₁ = 100 W/m².K. Determine the required gas-side surface area A₁ using the LMTD and & -NTU method.
Need answer ASAP In a counter-current-flow tubular heat exchanger, a liquid food (milk),flowing in the inner pipe, is heated from 20 to 40°C. In theouter pipe the heating medium (water) cools from 90 to50°C. The overall heat-transfer coefficient based on the insidediameter is 2000 W/(m^2-°C). The inside diameter is 5 cm andlength of the heat exchanger is 10 m. The average specific heatof water is 4.181 kJ/(kg-°C). Calculate the mass flow rate ofwater in the outer pipe. Compare the amount of milk being heated to concurrent design.
I am reviewing methods of assessing systems in heat transfer. One of the method I have run across for looking at single pass heat exchangers is log mean temperature difference (LMTD). What is the advantage of using LMTD instead of the basic/arithmetic difference in temperatures?
Outer surface of a tube-steel oven is at 110 oC. What would be the heat transfer rate tothe surrounding air at 25 oC. if the natural convective heat transfer coefficient ish = C (Ts – Ta)1/4where; C= 4.5 W/(m2.K5/4), Ta and Ts are air temperature and surface temperature,respectively. Surface area of the wall is 125 m2.(heat transfer by radiation can be neglected)
The local heat transfer coefficient of a flat plate that is obtained experimentally is equal to 9x^2+2ax+B. If the length of the plate is equal to 10 m. Determine the value of the average heat flux between the plate at 20 C and the air that is at 10 C. a = 4w/m^3.k and B is equal to 10W/m^2.k Select one: O a. 2890 W/m^2 O b. 3720 W/m^2 O c. 3500 W/m^2 O d. 1680 W/m^2
Q) The temperature of a heated plate is 88°C which is cooled by using pin-fins having a length of 5-cm, diameter of 1-cm, and thermal conductivity of (k=201 W/m-°C). The number of pins is (N=1800) and the temperature of the atmosphere is 10°C, while the convection heat transfer coefficient on the surfaces is 37 W/m2.°C. Assuming steady one-dimensional heat transfer along the fin and taking the nodal spacing to be 2.5-cm, determine (a) the temperature at the nodes along the fins, (b) the heat transfer rate from a single fin, (c) the heat transfer rate from all fins, and (d) the overall heat transfer rate from the heated plate which has dimensions of 0.6-m x 0.5-m with the fins.
Consider a thermoelectric plant with 30 MW of installed capacity and athermal efficiency of 24%. Determine the maximum pollutant concentration (in mg/m3) (y=0) and at ground level (z=0 and H=0), of a gas , for thefollowing situation:• Calorific value (Q=heat) of the gas = 35,000 kJ/kg.• Wind speed at a height of 10 m = 5.5 m/sIf the maximum limit allowed by the standard for gas X were 1 mg/m3, would the environmental impact be significant? Write the impact
Hello Sir, Good Afternoon.I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice, thank you.