closed tank 3m in diameter and 3m high is filled with water and rotates about its axis at 100 rpm. A pressure gage at the center of the top

Q: Question: The pressure pipe elbow with 30 degree orientation in the vertical plane is 60 cm in…

A: Solution

Q: Air Manometer fluid SG = 2.67. Oil SG = 0.87 P2 AGURE P3-134

A: Solution:- We know that the pressure difference in manometer between two point at same label pA-pB…

Q: Water is flowing into and discharging from a vertical pipe U-section as shown in Figure. At flange…

A:

Q: A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another…

A: Given data in question  Elevation heads at 2 points Pressure at 2 points Since the cross section at…

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

A:

Q: 11.34. If the pressure at point A in the figure is 300 kPa, compute the volume flow rate of water at…

A: Pressure at Point A =300 kPa

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

A:

Q: The system in Fig. 2-4 is at 70 °F. If the pressure at point A is 2900 lb/ft', determine the…

A:

Q: . Determine the velocity at the center of the pipe.

A: Level of water in pitot tube from top surface=20 cm Level of water in piezometer from top surface=35…

Q: → The diameter of a pipe carrying oil (s=0.92) changes gradually from 400 mm at A to 600 mm at B.…

A: Given data in question  Diameter  Pressure  Discharge  To find out  Direction of flow Frictional…

Q: Oil of specific gravity 0.82 flows through an orifice at the vertical side of a closed cylindrical…

A:

Q: 1. A closed cylindrical tank 1.50 in in radius and 2.5 in high is 3/4 full of oil (SG 0.90). If air…

A: Given      Radius of cylindrical tank, R = 1.5 in      Height of tank,H = 2.5 in      Oil filled in…

Q: Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter…

A: Given discharge= 120 L/s  Dia of horizontal pipe = 30 cm  Dia of vertical pipe = 20 cm

Q: Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in…

A: Discharge, Q=2 L/s Diameter of the pipe, D=50 mm Roughness coefficient, k=0.03 mm Opening diameter…

Q: Calculate the X length that can keep the gate closed. The gate is hinged from point A. The pressure…

A:

Q: 1.90m diameter closed cylinder, 2.75m high is completely filled with oil having sp.gr. of 0.8 under…

A:

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

A: Rate of flow the rate at which a liquid or other substance passes through a channel or conduit. The…

Q: Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1…

A: Piezometric head at point 1 is given by ;Piezometric head at point 2 is given by ;The water flows…

Q: The pressure in the tank is 50 psi. 10. Determine the value of equivalent pressure head of water. a.…

A: Using the definition of pressure at depth. The value of head for different fluids can be found.

Q: The pressure of compressed air on water surface in the tank shown in Fig. No. 2 is Pca 981 (KN/m2).…

A:

Q: a)Determine the difference in pressure between A and B in kPa if h = 0.15 and SG of oil is 0.862.…

A:

Q: Liquid 1 Liquid 2 h3 h1 h2

A: To find the pressure at the center of pipe using a manometer , we need to take a datum about which…

Q: Diameter= 6 in Diameter = 3in

A:

Q: A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other…

A:

Q: Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is…

A: NPSH is the net positive suction head, which is measured in the centrifugal pump.If the local…

Q: B: A closed cylindrical tank filled with water has a hemispherical dome and is connected to an…

A: Asked: To determine the pressure in pipe B and the pressure head, in millimeters of mercury, at…

Q: 1. A cube with 3 meters on each side weighs 1060 kiloNewton. It floats 1.8 meter depth of water…

A:

Q: The water is flowing with a velocity of 1.5 m/s in a pipe of length 2500 m and of diameter 500 mm.…

A: Using formula

Q: Diámetro 250mm Flujo de entrada LO Diámetro110mm E 90 cm en fl 0, 26 (

A:

Q: The velocity potential for a certaininviscid flow field is -(7xy-y) where o has the units of ft2/s…

A: Given,  Points: (1, 2) and (8, 8)  Given Velocity potential function=-(7x2y-y3] Our aim is to…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?