For the forces acting on the beam shown in Figure 3.1c, determine the location of the equivalent resultant force with reference to point A in m. Given a = 2.5, b = 2, P1 = 20, w1 %3D = 5 and w2 = 9. (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant force is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W2 kN/m W, kN/m A a m b m Figure 3.1c

For the forces acting on the beam shown in Figure 3.1c, determine the location of the equivalent resultant force with reference to point A in m. Given a = 2.5, b = 2, P1 = 20, w1 %3D = 5 and w2 = 9. (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant force is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W2 kN/m W, kN/m A a m b m Figure 3.1c

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: There is a structure composed of beam (AC) and truss (BD) as shown in the figure below. After trying…

A: E=29000kips/in2 To find displacement at B and C

Q: Problem 2 -A concentrated couple, = 600 Nm acts at the center of the simply Supported beam which is…

Q: 1. A homogeneous hemisphere of weight W and radius a rests on a perfectly smooth horizontal table as…

A: To find the tension in the string, we can use the principle of moments.. The weight of the…

Q: A non-prismatic rod is attached between two supports as shown in figure. It is subjected to axial…

A: Given :- E =200 GpaAAB= 300 mm2 =450 mm2

Q: A propped cantilever beam is loaded by a bending moment of the magnitude M, at the point B as shown…

Q: A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The…

Q: F2 -300 N F=700 N 60 M. =1500 Nm 2 m 3m or the above diagram, given that F, = 450 N, 8 = 30 degrees…

Q: Solve with clear step by step solutions

A: if you any doubt please comment

Q: The resultant of the three forces as shown in figure is vertical. determine the angle 0, and…

A: All data present in the figure Need to find 1- Resultant force (R)2- angle ()

Q: A non-prismatic rod is attached between two supports as shown in figure. It is subjected to axial…

A: For a non prismatic rod Axial load applied is 80 kN and 100 kN as shown in figureTo determine…

Q: PROBLEM3: For the system shown in Figure 1, x and y denote, respectively, the absolute displacements…

Q: A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The…

Q: Having found Fcp in the analysis of joint C, there are now only two unknown forces acting on joint…

A: Method of Joints: Consider the free body diagram of the given truss as shown below. Consider the…

Q: A truss (Truss) is subjected to force as shown in the figure below. Try to calculate the vertical…

A: A=200mm2 E=200GPa To find vertical displacement at point C

Q: A symmetrical beam of length I has a cantilever support at the left hand end x = 0 and a pin support…

Q: In the frame shown below, P is equal to 208. what is the value of the Vertical direction reaction…

Q: Example : Resolve the horizontal 600 N force in shown into components acting along the u and v axes…

Q: The beam shown in the figure is subjected to a moment of M = 50 kN.m. Determine the bending stress…

A: Bending stress at point A is given as ; σA = M*yAIN-A M = Moment = 50 KNm = 50 * 106 yA = Distance…

Q: Problem#1 Given: The uniaxial bar shown below is homogeneous, prismatic and has an evenly…

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

For the forces acting on the beam shown in
Figure 3.1c, determine the location of the
equivalent resultant force with reference to
point A in m. Given a = 2.5, b = 2, P1 = 20, w1
%3D
= 5 and w2 = 9.
(Note: Prefix the answer with negative sign
"." if the location is to the left of the
reference point. E.g. if the location of the
equivalent resultant force is located
between points A and B, or to the left of
point B by 1.2m, the answer should be "-1.2"
with reference to point B)
P, kN
W2 kN/m
W, kN/m
A
a m
b m
Figure 3.1c

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w 36 kN/m over 1.5 m from the left-hand end and moment loading M = 44 kNm at 1.5 m from end B. - Determine the reaction force at support A. Input your answer as a value only in KN to one decimal place and without +/- sign. w kN/m M kNm B A X -1.5 m -1.5 m -1.5 m-
Figure 2 below shows a 600 N force, F, acting on a pipe. Z i. ii. 6 m F = 800 N B 7m 5 m A 8 m Figure 2 Express F as a cartesian vector. Determine the component of F acting along the pipe, OA.
For the forces acting on the beam shown in Figure 3.1f, determine the location of the equivalent resultant force with reference to point B in m. Given / = 1.5, P1 = 5, P2 = 20 and w = 4 (Note: Prefix the answer with negative sign "-" if the location is to the left of the reference point. E.g. if the location of the equivalent resultant is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W kN/m |P2 kN 21 m 21 m Figure 3.1f
Q2 In the figure below, R is the resultant of the two forces F1 and F2. Determine the magnitude and direction of the force F2 F1 = 150 N Clox R = 280N 32
A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
SOLVE THE FOLLOWING PROBLEM AND SHOW YOUR COMPLETE SOLUTIONS. EXPLAIN YOUR ANSWER FOR BETTER UNDERSTANDING.