A circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm. A circular solid shaft made of vibranium has G=80 MPa and has a limiting torsional shear stress of 60 MPa.Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1-10 kN-m and T2-25 kN-m.Answer in mm.T1Tpf-1.5 m 2.5 m1 m

Answered: Image /qna-images/answer/554d2c98-7ac6-415d-b34f-6f68432cd30b.jpg

circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm.

circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

64. A solid circular shaft of diameter d and length L is fixed at one end and free at the other end. A torque t is applied at the free end. The shear modulus of the material is G. The angle of twist at three free ends is O A. O B. O C. O D. 16TL Td4G 32TL πd4G 64TL Td4G 128TL πd4G
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
A solid shaft has an allowable shear stress of 37 MPa and transmits a torque of 1236 Nm. Determine the minimum diameter of the shaft in mm (give answer correct to 2 decimal places).
Two solid steel wall supported shafts are connected using the 4 bolt flange. A torque is applied to one side of the bolted connection. Using G = 11.2x10 psi determine the shear stress in the 4" diameter bolts which are on a 2.5" bolt circle diameter. Solve with the applied torque on the left side coupling as shown. Also determine the bolt shear stress if the applied torque was on the other side of the coupling. 1.5 in. 1.25 in. T-350 lb ft 3 ft 2 ft
4-Determine the rotation angle between A and C, if the torque is T=0.9 N.m in point C, if G=80 GPa and diameter of all shafts are D=4 mm. (The radius of small circle are r and the bigger one are 2r) e are Coder 40 T=09N.N
The 60-mm-diameter shaft is made of 6061-T6 aluminum having allowable shear stress of tallow = 80 MPa. Determine the maximum allowable torque T. Also, find the corresponding angle of twist of disk A relative to disk C.
Determine the angle of twist of the end A of the A-36 steel shaft shown in Fig.a. Also, what is the angle of twist of A relative to C? The shaft has a diameter of 200 mm.
The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure 1.20 m 1.20 m 1 of 1 Part A If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.060 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. T = Submit Value Provide Feedback Request Answer Units ?
A steel shaft 2542 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.
I cant figure out how to do this problem how do I do it?
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.