Chromel is an alloy composed of nickel, iron, and chromium. A 0.6418-g sample was dissolved and diluted to 250.0 mL. When a 50.00-mL aliquot of 0.05173 M EDTA was mixed with an equal volume of the diluted sample, all three ions were chelated, and a 5.27-mL back-titration with 0.06139 M copper(II) was required. The chromium in a second 50.0-mL aliquot was masked through the addition of hexamethylenetetramine; titration of the Fe and Ni required 35.81 mL of 0.05173 M EDTA. Iron and chromium were masked with pyrophosphate in a third 50.0-mL aliquot, and the nickel was titrated with 25.77 mL of the EDTA solution. Calculate the percentages of nickel, chromium, and iron in the alloy. Percentage of nickel = % Percentage of iron = 1% Percentage of chromium =

Chromel is an alloy composed of nickel, iron, and chromium. A 0.6418-g sample was dissolved and diluted to 250.0 mL. When a 50.00-mL aliquot of 0.05173 M EDTA was mixed with an equal volume of the diluted sample, all three ions were chelated, and a 5.27-mL back-titration with 0.06139 M copper(II) was required. The chromium in a second 50.0-mL aliquot was masked through the addition of hexamethylenetetramine; titration of the Fe and Ni required 35.81 mL of 0.05173 M EDTA. Iron and chromium were masked with pyrophosphate in a third 50.0-mL aliquot, and the nickel was titrated with 25.77 mL of the EDTA solution. Calculate the percentages of nickel, chromium, and iron in the alloy. Percentage of nickel = % Percentage of iron = 1% Percentage of chromium =

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter17: Complexation And Precipitation Reactions And Titrations

Section: Chapter Questions

Problem 17.34QAP

See similar textbooks

Related questions

Q: 6. Titration of Ca²+ and Mg2+ in a 50.00-mL hard water sample required 23.65 mL of 0.01205 M EDTA. A…

A: A question based on environmental pollution that is to be accomplished.

Q: A 50.00 mL sample of hard water is titrated with 0.0102 M EDTA solution (volume of blank titration=…

A: Given data,Volume of sample=50mLMolarity of EDTA=0.0102MVolume of EDTA=22.44mLVolume of EDTA for…

Q: The %(w/w) I in a 0.6712 g sample was determined by a Volhard titration. After adding 50.00 mL of…

Q: A solution containing chloride ion was analyzed by the Volhard method. A 50.00 mL sample containing…

A: Given, MAgNO3 = 0.2500 M VKSCN = 25.00 mL = 0.025 L MKCN = 0.2380 M VKSCN = 10.67 mL = 0.01067 L

Q: Calculate the molar solubility of calcium oxalate in a solution that has been buffered so that its…

A: The molar solubility of calcium oxalate in a solution at different pH is as follows-

Q: Standard CaCO, is used to standardize the EDTA solution prior to titration. Suppose 0.385 g of CaCO,…

Q: 47.6 mL aliquot from a 0.5 L solution that contains 0.45g of MnSO4 (MW is 151 g/mol) required 41.9…

Q: Cl- is precipitated by addition of AgNO3?

A: Given Cl- is precipitated by addition of AgNO3?

Q: A 0.4108-g sample of primary-standard Na2 CO3 was treated with 46.50 mL of dilute perchloric acid.…

Q: An antacid tablet, weighing 1.25 g, was dissolved in a 1.0 L volumetric flask to allow for…

A: Given data,Mass of tablet=1.25gVolume of solution=1.0LVolume of aliquot=10.0mLMolarity of…

Q: 2. You are measuring the Fe(lI) content of a sample of FeCl2.4H20. You weighed out 1.20g FeCl2.4H20…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A solution was prepared by dissolving 2.8 grams of EDTA (Na2H2Y.2H2O) in 1 L of water. This solution…

A: Reaction taking place during the Standardization of EDTA is,

Q: This EDTA solution is used to analyze a piece of 0.0630 g of metal alloy containing Sn and Cu that…

A: This question is based on estimation of composition of alloy by using EDTA titrations. In the given…

Q: A sample containing calcium was analyzed by gravimetry, converting all calcium to calcium oxalate…

A: Given that the precipitate is calcium oxalate monohydrate.

Q: Li, „CoO, is an anode for lithium batteries. Cobalt is present as a mixture of Co(III) and Co(II).…

A: First, we have to find the unreacted mmoles of Fe2+ from K2Cr2O7 titration. The find out the total…

Q: 1. A 0.9882 gram sample of iron ore is dissolved, the iron reduced to Fe2+, and the solution was…

A: #1: Given the mass of the iron ore sample = 0.9882 g Volume of 0.02065 M KMnO4 used for the…

Q: The amount of Fe in a 0.4891-g sample of an ore is determined by titrating with K2Cr207. After…

A: Indicator is the chemical substance that adds to the analyte solution to know the end point…

Q: A 0.2420 g sample cntg. Calcium is dissolver and the metal precipitated as CaC2O4. The ppt. is…

A: Solution - According to the question - Given -

Q: KClO3 in a 0.1862 g sample of an explosive was determined by the reaction with 50.00 mL of Fe2+…

A: Given that - Mass of KClO3 sample = 0.1862 g Volume of Fe2+ Solution = 50.00 mL Molarity of Fe2+…

Q: A sample of mineral water containing Ca and Mg was analyzed by a complexation titration using EDTA…

Question

Chromel is an alloy composed of nickel, iron, and chromium. A 0.6418-g sample was dissolved and diluted to 250.0 mL. When a 50.00-mL aliquot of
0.05173 M EDTA was mixed with an equal volume of the diluted sample, all three ions were chelated, and a 5.27-mL back-titration with 0.06139 M
copper(II) was required. The chromium in a second 50.0-mL aliquot was masked through the addition of hexamethylenetetramine; titration of the Fe
and Ni required 35.81 mL of 0.05173 M EDTA. Iron and chromium were masked with pyrophosphate in a third 50.0-mL aliquot, and the nickel was
titrated with 25.77 mL of the EDTA solution. Calculate the percentages of nickel, chromium, and iron in the alloy.
Percentage of nickel =
%
Percentage of iron =
Percentage of chromium =
%
%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

Chromel is an alloy composed of nickel, iron and chromium. A 0.6553-g sample was dissolved and diluted to 250.0 mL. When a 50.00-mL aliquot of 0.05173 M EDTA was mixed with an equal volume of the diluted sample, all three ions were chelated, and a 5.34-mL back titration with 0.06139 M copper (II) was required.The chromium in a second 50.0-mL aliquot was masked through the addition of hexamethylenetetramine; titration of the Fe and Ni required 36.98 mL of 0.05173M EDTA. Iron and chromium were masked with pyrophosphate in a third 50.00-mL aliquot, and the nickel was titrated with 24.53 mL of the EDTA solution. Calculate the percentage of Cr in the alloy. Express your answer in 2 decimal places.
Iron(III) is best determined by addition of excess EDTA, followed by back-titration with a metal ion that reacts rapidly with EDTA. A 700.0-mg sample is dissolved, 20.00 mL of 0.0500M EDTA is added, and the excess EDTA is titrated with 5.08 mL of 0.0420M copper(lI). Calculate the percentage of Fe,O, in the sample.
Chromel is an alloy composed of nickel, iron and chromium.A 0.6472 g sample was dissolved and diluted to 250 mL. When a50 mL aliquot of 0.05182 M EDTA was mixed with an equal volumeof the diluted sample and all the three ions were chelated, a 5.11 mLback titration with 0.06241 M copper (II) was required.The chromium in a second 50 mL aliquot was masked through theaddition of hexamethylenetetramine, titration of the Fe and Nirequired 36.28 mL of 0.05182 M EDTA.Iron and chromium were masked with pyrophosphate in a third50 mL aliquot and the nickel was titrated with 25.91 mL of theEDTA solution.Calculate the percentage of nickel, chromium and iron in thealloy.
0.0322 M EDTA solution is used as the titrant in the titration of a 50.00 mL solution that is 0.0129 M in Cu2+. The solution is held at pH = 10.00 by a buffer that is 0.050 in ammonia (NH3). At what volume (in mL) of EDTA added will the equivalence point be reached?
The Zn in a 0.7556-g sample of foot powder was titrated with 21.27 mL of 0.01645 M EDTA. Calculate the percentage of Zn in this sample. A silver nitrate solution contains 14.77 g of primary-standard grade AgNO3 in 1.00 L. What volume of this solution will be needed to react with 0.2631 g of NaCl.
A 300.00 ml solution of HBr was treated with 5 ml of freshly boiled and cooled 8 M HNO3, and then with 50.00 mL of 0.3650 M AgNO3 with vigorous stirring. Then 1 mL of saturated ferric alum was added and the solution was titrated with 0.2870 M KSCN. When 3.60 mL had been added, the solution turned red. What was the concentration of HBr in the original solution? How many milligrams of Br- were in the original solution?
2
An alloy containing Ni, Fe and Cr was analyzed by a complexation titration using EDTA as titrant. A 0.7176 g sample of the alloy was dissolved in HNO3 and diluted to 250 mL in a flask. A 50.00 mL aliquot of the sample, treated with pyrophosphate to mask Fe and Cr, required 26.14 mL of 0.05831 M EDTA to reach the murexide endpoint. A second 50.00 mL aliquot was treated with hexamethylenetetramine to mask Cr and titration with 0.05831 M EDTA required 35.43 mL to reach the murexide endpoint. Finally, a third 50.00 mL aliquot was treated with 50.00 mL of 0.05831 M EDTA and titrated back to the murexide endpoint with 6.21 mL of 0.06316 M Cu(II). the weight percentages of Ni, Fe and Cr in the alloy.
A salt sample was analyzed for its purity. A 0.5000 g sample was dissolved in water and diluted to 250 mL. From this solution, 25.00 mL was taken for analysis. To this aliquot, 20.00 mL of a 0.08735 M AgNO3 solution was added to precipitate the chloride. The excess AgNO3 required 12.45 mL of a 0.09473 M KSCN solution for back-titration. Calculate the purity of the salt sample as percent by mass of KCl (74.55 g/mol)
A 25.00 mL aliquot of sample containing Hg in dilute nitric acid was treated with 10.00 mL of 0.04882 M EDTA and the pH was adjusted to 10. The excess EDTA was titrated with 24.66 mL of 0.01137 M Mg. What is the molarity of Hg in the original solution?
A 0.2420 g sample cntg. Calcium is dissolver and the metal precipitated as CaC2O4. The ppt. is filtered, washed and redissolved in acid. The pH is adjusted, 25 ml of 0.0400 M EDTA added and the xcss EDTA titrated with 33.28 ml of 0.012102 M MG2+. Calculate the % Ca (40.078) in the sample.
A1.3174-g sample containing the chloride salts of magnesium, mercury(II), and zinc was dissolved in 250.0 ml of solution. A 50.00-mL aliquot was treated with 1o ml of an NH,/NH,CI buffer at pH 10 followed by 25.00 ml of o.o5331 M EDTA. After a few minutes of mixing, the excess EDTA was back titrated with 11.43 mL of o.o1816 M MagCl.. A second 50.00-mL aliquot was made basic and treated with excess NaCN, complexing both the mercury and zinc. The magnesium in this sample required 16.83 mL of o.005583 M EDTA for titration. The solution remaining at the end point of this titration was treated with excess formaldehyde, which reacts with the free CN and Zn(CN),: OH CN + HCHO + H.O H.C + OH CN The liberated Zn" required 28.47 mL of the EDTA for titration. Calculate the percentage of each metal in the sample. Answer: 0.8669 % Mg: 3.94 % Zn; 19.4 % Hg