A sample of mineral water containing Ca and Mg was analyzed by a complexation titration using EDTA as the titrant. A 50 ml aliquot of the sample was rendered strongly alkaline to precipitate the Mg as Mg (OH)2. Titration with a calcium specific indicator required 20 ml of 0.02M EDTA. A second 50 ml aliquot was adjusted to pH 10 titrating with 0.02M EDTA required 32.50 ml of 0.02M EDTA. Calculate the ppm CaCO3 (MW=100g/mol) and ppm M9CO3 (MW=84 g/mol) in the mineral water.

A sample of mineral water containing Ca and Mg was analyzed by a complexation titration using EDTA as the titrant. A 50 ml aliquot of the sample was rendered strongly alkaline to precipitate the Mg as Mg (OH)2. Titration with a calcium specific indicator required 20 ml of 0.02M EDTA. A second 50 ml aliquot was adjusted to pH 10 titrating with 0.02M EDTA required 32.50 ml of 0.02M EDTA. Calculate the ppm CaCO3 (MW=100g/mol) and ppm M9CO3 (MW=84 g/mol) in the mineral water.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The Telluride ion was determined by indirect titration with EDTA. To a solution containing 50.00 mL of 0.08664M Zn(CIOA)2 plus 15 mL of 1 M acetate buffer (pH 4.5) were added 50.00 mL of unknown telluride solution with vigorous stirring. The ZnTe precipitate was filtered and washed with hot water. Then NH3 was added to the filtrate (which contained excess Zn2+) until the blue colour of Zn(NH3)42+ was observed. Titration of the filtrate with 0.07854 M EDTA required 24.22 mL to reach the murexide end point. Calculate the molarity of telluride ion in the unknown.
A 50.00 ml aliquot of a solution containing Ca2+ and Mg2+ was buffered at pH 10 and titrated with 0.0418 M EDTA. The endpoint volume was 44.36 ml. A second aliquot of the same mixture was made strongly basic by the addition of NaOH – this causes the Mg2+ to precipitate as Mg(OH)2. The solution was then titrated with the 0.0418 M EDTA and the endpoint volume was found to be 30.02 ml. Calculate the molar concentration of Mg.
A solid containing tris was dissolved in water and brought to a total volume of 50.00 ml. A 10.00 ml aliquot of the solution was titrated with 0.09978 M HCl to a bromcresol green endpoint. The aliquot consumed 38.93 ml of titrant. Calculate the weight of tris in the original sample.
Nitroethene, CH2CHNO?, is a very labile compound that must be prepared with care. Ifpurification of nitroethene s attempted, generally only small amounts are recovered, but theinner walls of the distillation apparatus are covered with a white film. Explain.
A 1.000 mL aliquot of a solution containing Cu²+ and Ni²+ is treated with 25.00 mL of a 0.03703 M EDTA solution. The solution is then back titrated with 0.02138 M Zn²+ solution at a pH of 5. A volume of 22.13 mL of the Zn²+ solution was needed to reach the xylenol orange end point. A 2.000 mL aliquot of the Cu²+ and Ni²+ solution is fed through an ion-exchange column that retains Ni²+. The Cu²+ that passed through the column is treated with 25.00 mL of 0.03703 M EDTA. This solution required 18.53 mL of 0.02138 M Zn²+ for back titration. The Ni²+ extracted from the column was treated witn 25.00 mL of 0.03703 M EDTA. How many milliliters of 0.02138 M Zn²+ is required for the back titration of the Ni²+ solution? volume: mL
One of the following is correct due to determination of Ca2* by quantitative precipitation and titration a. The titration against K2Cr207 was carried out at temperature range 50-60 °C b. The oxidizing agent used was KMNO4 c. Oxalic acid was used as the primary standard d. Oxidation using permanganate should be proceed only in basic solution
0.0585g of Na2C2O4, 10 mL of distilled water and 2 M H2SO4 were added to adjust the KMnO4 solution prepared as 0.1M. Heating process was carried out and 8.4mL of titrant was consumed as a result of titration. Calculate the true concentration of potassium permanganate accordingly.
1. A 0.7120 g of iron ore was brought into solution and passed through a Jones reductor. Titration of Fe(II) produced required 39.21mL of 0.02086M KMnO4. Express the results of analysis in terms of (a) percent Fe (MM 55.85) and (b) percent Fe₂O3 (MM 159.69). 5Fe +2 + MnO4 +8H+ → 5Fe+³+ Mn+² + 4H₂O
Calculate PCa of the solution that results when 50.0 mL of 0.0050 M Ca2+ is titrated with 25.00 mL of 0.0100 M EDTA in a solution buffered to a conastant pH of 10.00.
0.4545 g CaCO3 was dissolved in HCl and the resulting solution was diluted to 0.25 L. Twenty-five mL aliquot of this solution required 35.2 mL of EDTA upon performing titrimetric analysis. Determine the molarity of EDTA
An unknown solution containing 25.00 mL of Ni2+ in dilute HCl is treated with a known excess of 25.00 mL of 0.05382 M EDTA solution. The solution turns yellow when a few drops of indicator are added. The excess unreacted EDTA back titrated with 0.02299 M Zn2+, which requires 17.00 mL to reach the red end point. What is the molarity of Ni2+ in the unknown solution?
A 1.00 mL aliquot of a solution containing Cu and Ni is treated with 25.00 ml. of a 0.03468 M EDTA solution. The solution is then back titrated with 0.02308 M Zn+ solution at a pH of 5. A volume of 20.28 ml. of the Zn solution was needed to reach the xylenol orange end point. A 2.000 mL aliquot of the Cu* and Ni* solution is fed through an ion- exchange column that retains Ni?*. The Cu?+ that passed through the column is treated with 25.00 mL of 0.03468 M EDTA. This solution required 23.18 mL of 0.02308 M Zn* for back titration. The Ni extracted from the column was treated witn 25.00 mL of 0.03468 M EDTA. How many milliliters of 0.02308 M Zn+ is required for the back titration of the Ni solution? volume: ml.