Choose the correct answer1- The resistivity of the conductor depends on(a) area of the conductor(c) type of material.(b) length of the conductor(d) none of these2-The resistance of a conductor of diameter and length / is R 22. If the diameter of theconductor is halved and its length is doubled, the resistance will be(c) 4R Ω (d) 8R Ω(a) RΩ(b) 2R Ω(b) 2R Ω3- How many coulombs of charge flow through a circuit carrying a current of 10 A in 1minute?(a) 10 (b) 60 (c) 600 (d) 12004- Internal resistance of ideal current source is(a)Zero (b)Infinite (c)(c) Finite (d) 100 ohmsFinite5- For the circuit shown in Fig. 1, the current in the 12 resistor is.(a) SAA(b) 10A(c)15A10 V(d) zero#sv5 VFwwwFig.110

Answered: Image /qna-images/answer/ee13ca82-888b-45e9-ae35-d806083e57d0.jpg

Choose the correct answer 1- The resistivity of the conductor depends on (a) area of the conductor (c) type of material. (b) length of the conductor (d) none of these 2-The resistance of a conductor of diameter & and length / is R 2. If the diameter of the conductor is halved and its length is doubled, the resistance will be (c) 4R Ω (d) 8.R 2 (a) RΩ (b) 2R Ω (b) 2R Ω 3- How many coulombs of charge flow through a circuit carrying a current of 10 A in minute? (a) 10 (b) 60 (c) 600 (d) 1200

Choose the correct answer 1- The resistivity of the conductor depends on (a) area of the conductor (c) type of material. (b) length of the conductor (d) none of these 2-The resistance of a conductor of diameter & and length / is R 2. If the diameter of the conductor is halved and its length is doubled, the resistance will be (c) 4R Ω (d) 8.R 2 (a) RΩ (b) 2R Ω (b) 2R Ω 3- How many coulombs of charge flow through a circuit carrying a current of 10 A in minute? (a) 10 (b) 60 (c) 600 (d) 1200

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The length of AWG# 0000 copper wire that has a resistance of 4.9 Ω@ 20°C is
proper explanation
can you solve this? Please write well
Answer 2
Consider the circuit segment shown in the figure below. GivenE1 = 1.94 V, E2 = 9.67 V, R1 = 36.8 kΩ, R2 = 65.9 kΩ, I1 = 34.4 µA, themagnitude of the current passing thru the second resistor is most nearly
Five pieces of copper wire have the following description, rank the following resistance from lowest to highest R1 R2 R3 R4 RS Length L Diameter D Twice Diameter D One half Diameter D One half Length L Three quarter Length L Twice Length L One three Length L One half Diameter D One half Diameter D O R1, R4, R3, R2, and R5 O R5, R1, R4, R3 and R2 O R4, R1,R5, R3 and R2 O R2, R1, R5, R3 and R4 O R4, R3, R5, R1 and R2 O none of the above
answer thanks.
As the temperature of a conductor increases the resistance of the conductor decreases. Select one: O True False
Note: please solve the correct solution
Question 3. (a) A 1.00 km cable having a cross-sectional area of 0.5 cm? is to be constructed out of equal lengths of copper and aluminium. The resistivity values of copper (Cu) and aluminium (Al) material are pcu = 1.68 x 108 Qm and PAI = 2.65 x 108 Qm, respectively. Two designs could be used to make the 1.00 km cable as shown in Figure Q3(a)(i) and Figure Q3(a)(ii). +1.00 km- Cu Al A-0.5 cm2- F1.00 km- O Cu ) Al 0.5 km 0.5km (i) (ii) Figure Q3(a) (i) First design of the cable is to solder side by side of the two parallel 1.00 km copper and aluminium cables as shown in Figure Q3(a)(i). The cross-sectional areas of copper and aluminium cables are halved of that of the constructed cable. Calculate the total resistance of the cable. (ii) Second design of the cable is to solder a 0.50 km aluminium cable at the end of a 0.50 km copper cable as shown in Figure Q3(a)(ii). Calculate the total resistance of the cable. (iii) Justify which design of the cable gives better electrical performance.…
Determine the resistance and conductance of 20m of copper wire 2mm in diameter. S=8^-10*1.72= 1-72x10_r.m.
TaqooD fOusul AllaS The DC distributor fed at one end as shown below, the resistance of each conductor per 100m is 0.040 voltage at point B is maintain at 300V, then find The total voltage drop in this distributor (2 Marks) (1) The minimum voltage value in distributor (1 Mark) ion (ii) The total power losses in distributor (2 Marks) C E 150m | 200m 100m 250m 40A 50A 80A 60A 1 A- BI A single phase ring distributor ABCA is fed at point A, the feeding point maintains at 300 /0° V. the load at point B 07/04 a 49 立