4. A square loop carrying a current I = 5 A is located as shown in Figure 3. A straight, long conductor carrying a current I' = 10 A is introduced and placed just above the midpoints of two of the loop's sides. If a = 1 m, determine the net force acting on the loop. straight long conductor square loop of side 2a Figure 3

4. A square loop carrying a current I = 5 A is located as shown in Figure 3. A straight, long conductor carrying a current I' = 10 A is introduced and placed just above the midpoints of two of the loop's sides. If a = 1 m, determine the net force acting on the loop. straight long conductor square loop of side 2a Figure 3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ex-6
What is difference in loop and mesh?
123 only
Dear sir Hand written solution is not allowed.
please answer part d, e and f
For the magnetic system given below, assume infinite permeability for the core. 1=0.5 A 6 cm- N = 1000 turns Core cross-section: 2 cm x 2 cm -6 cm 4 mWb 8 mWb 0 mWb 10 mWb $₂ 0.5 cm 8 cm The flux in the air gap (ignoring fringing) would approximately be
to the primary side. Question # 3 The coils of the magnetic circuit shown in the figure are connected in series. They are wound with equa turns of 100 turns each. The dimensions are: Cross-section area of A and B legs 7 cm2 Cross-section area of C leg 14 cm? Length of A path is 17 cm Length of B path is 17 cm Length of C path is 5.5 cm Length of the air gap is 0.4 cm The material has a constant relative permeability of H of 2800. Neglect the fringing effect and leakage flux. 00 %3D Calculate the current required to produce a flux density of 1.2 T in the air gap.
The magnetic moment for the circular loop with side a and current I is a. zero O b. па2 O c. 2π al O d. 4/3 πa³1
PLEASE HELP ME CHOOSE WHAT CORRECT LETTER OR ANSWER 4. The induced voltage in a single loop reverses a. once each revolution. b. once each half-revolution. c. twice each half-revolution. d. twice each revolution. e. three times each revolution. 5. Maximum voltage is induced in a single loop when the sides of the loop are passing a. perpendicular to the lines of force. 6. b. parallel to the lines of force. c. not quite perpendicular to the lines of force. d. at a slow rate of speed. e. in front of the N pole face. When a commutator is used on a single loop, the voltage at the brushes has a a. very large magnitude. b. changing polarity. c. constant polarity. d. zero value. e. constant value. 7. The left-hand generator rule is typically used to determine a. conductor speed. b. rotational direction. c. field direction. d. current direction. e. magnetic field strength.
2. The parallel conductors of 10 mm diameter each carry 100 A in opposite directions are separated by an air space of 50 mm. The conductors are 10 m long. The force on each conductor will be
The corecivity of a small magnet where the ferromagnet gets demagnetized is 3 x 10³ Am-¹1 The current required to be passed in a solenoid of length 10cm and number of turns 100, so that the magnet gets demagnetized when inside the solenoid is:
You have measured both of the series and shunt field windings and found that each has over 10 mega ohm to ground. Your ohm meter, however indicates a resistance of 1.5 ohms across terminals S1 and S2. The ohmmeter indicates a resistance of 225 ohms between terminal F1 and F2. Are these readings normal for this type of machine, or is there likely a problem?