change in molar specific enthalpy

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

A:

Q: What is the CGS unit of surface tension?

A: Given: Surface tension: It is the surface force in the liquid to shrink into the minimum possible…

Q: If the cylinder in Problem 6 has a stroke of 40 cm, what is the maximum cycle rate that might be…

A:

Q: You are the engineer of a company that manufactures a specific component using a CNC machine. The…

A:

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: Sketch the normal and tangential coordinates and the acceleration vector and on each airplane for…

A: Acceleration is the rate of change of speed per unit time. Speeding up means the airplane has…

Q: What are the benefits of CHP(combined heat & power) application? i need to do a presentation. can…

A:

Q: Q1:- (a) – Give an explanation for each the following:- 1- The design mistake is very dangerous…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Which one is wrong about the traditional manufacturing methods?(Alışılmış O A) Team vibration is…

A: The cutting speed of a material depends upon several factors.

Q: In a mechanical shopfloor it produce shafts, The shopfloor established with design capacity is 30…

A: Given,  Design capacity = 30 shafts/day Effective capacity  = 20 shafts/day Current capacity  = 27…

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: A selection between advanced machining operation and conventional machine operation is to be made…

A: Given dataMachining process is electrochemical machiningThinkness of stinless steel plate t=…

Q: What is the flow rate to a cylinder with a 3-in bore and 22-in stroke that fully extends in 8…

A:

Q: 37. Increasing the absolute humidity of the air, the value of the drying rate constant, R a.…

A: Given data :- Absolute humidityDrying rate To determine :-  Dependencies of both quantity

Q: why is the kinetic energy for this problem only rotational? Thank you!

A: Given: Motion of the point A will be in horizontal direction and the motion of the point B will be…

Q: 22.33 In Table 22.1, the last tw o properties listed can be

A: The general characteristics of tool materials is given.

Q: Give 3 example of an application of the Lever Rule.

A: The compositions of the phases present are determined using the lever rule. The lever rule is also…

Q: Can someone identify this icon's description in Fusion 360?

A: Solution: Given Data:   To Find: Identify the description of each of the given icon in Fusion 360.…

Q: In exponential smoothening method,

A: Given; Exponential smoothening method,  Which one of the following is true,Where,   Exponential…

Q: 1. A shaft made of steel having an ultimate strength of Su is finished by grinding the surface. The…

A:

Q: 63. The process of impression a diamond-shaped or straight-line pattern into the surface is called…

A: Knurling is a manufacturing process, typically conducted on a lathe, whereby a pattern of straight,…

Q: When does the Stress concentrations occur in shafts?

A: A resisting force produced in a body on each unit area to counter the deformation of the body is…

Q: 8. Explain what is meant by mean effective pressure. A four cylinder, four stroke cycle petrol…

A:

Q: A forging press plant must be planned to manufacture engine components as per the details given.…

A:

Q: Knowing that time is of the essence determine the best method to identify if the mix bars are AISI…

A: Both AISI 1020 and AISI 1040 are alloys of iron with their average alloy composition basically…

Q: lease compare the efficiency of a tubular bowl centrifuge to a disc-stack centrifuge. The comparison…

A: Frame, bowl, motor, and starter make up the Tubular Bowl Centrifuge. The bowl revolves at 15000 rpm,…

Q: a Buyer at Tesla and just received 18,000 tires from Michelin. The floor has discovered an issue…

A:

Q: Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, each 32x32x150 mm.…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: 16)In which process Catcher is used

A: Catcher is used in abrasive water jet machining According to question option c is absolutely correct

Q: Suppose that a company that works in extruding aluminium products has spent L.E. 50,000 on…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: 1- The pure aluminum and the copper are generally rated as easy to machine 2- In ultrasonic…

A: As per the guidelines  only three sub parts of a question can be solved at a time please repost the…

Q: Explain revision B?

A: As you can see in below image, at highlighted location, in revision B, there is diameter with upper…

Q: 3. what are individual efficiencies that affect operation ?

A: Given Data : Individual efficiency Operation

Q: determine the rate of reciprocation in rpm.

A: first of all find out volume flow rate at pneumatic cylinder condition with the help of ideal gas…

Q: How’s ASTM D2041 related to ASTM D2726 ??

A: Solution is attached below:

Q: Solve any question with heat using the chain rule with a mathematical application, not an…

A:

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.