Certain mole of charcoal (12C) has to be completely converted to CO2 after reaction with the oxygen of air. If double amount of air (mole basis) was supplied in the reactor then find the average molecular weight of the outlet gas mixture stream. Note that, carbon has no reaction with nitrogen in this case.

Certain mole of charcoal (12C) has to be completely converted to CO2 after reaction with the oxygen of air. If double amount of air (mole basis) was supplied in the reactor then find the average molecular weight of the outlet gas mixture stream. Note that, carbon has no reaction with nitrogen in this case.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter23: Potentiometry

Section: Chapter Questions

Problem 23.11QAP

See similar textbooks

Similar questions

Propane is dehydrogenated to from propylene in a catalytic reactor: C3H8 → C3H6 + H2 The process is to be designed for a 95% overall conversion of propane. The reaction products are separated into two streams: the first, which contains H2, C3H6, and 0.555% of the propane that leaves the reactor, is taken off as product; the second stream, which contains the balance of the unreacted propane and 5% of the propylene in the product stream, is recycled to the reactor. Calculate the composition of the product, the ratio (moles recycled)/(moles fresh feed), and the single-pass conversion.
Some ionic can include in their solid structures in specific proportions. For example anhydrous copperII sulfate form a hydrate according to the reaction equation below. Determine the number of water moléculas in the hydrate ( x in the equation) from the following information. A 1.000g sample of anhydrous CuSO4 adsorbed water and became completely hydrated. This sample then weighed 1.65g CuSO4+x H2O --> CuSO4 . x H2O
Consider the following simultaneous reactions: N2 + 3H2 → 2NH3(a) H2 + CO2 → CO + H2O (b) 550 mols are fed into the reactor, initially containing 67.4% H2, 21.3% N2 and the remainder CO2. The mixture at the outlet has 16% NH3 and 5% H2O (molar percentages). a- Calculate the degrees of advancement of reactions (a) and (b).
A pilot plant reactor was charged with 50 kg naphthalene and 200 kg (98% by wt) H2SO4. The reaction  goes to 90% completion. The product distribution was found to be 18.6% monosulfonate naphthalene and 81.4% disulphonate naphthalene. Calculate the complete analysis of the product.
1. Kindly answer this problem. Thank you.
MBA Corp plans to use its idle building that can potentially be rented for $15,000 per annum to set up a manufacturing machinery there. The current Revenue of MBA Corp is $500,000. If the company takes up this project, its revenue is expected to increase by 30% for the next three years and then double (from the 3rd year level) for the next two years. After 5 years, the project will be scrapped and the salvage value is expected to be $80,000 The COGS are expected to remain the same at 60% of revenue. The SG&A and other operating costs will increase by $10,000. The cost of the machinery is expected to be $250,000. The machinery installation cost is expected to be $20,000. This investment will require additional inventory of $40,000 and increase the accounts payable by $20,000 The company spent $ 5000 in researching the viability of the building for machine installation. The company hires you as a financial manager to advise if they should take up this project or not. Other information:…
please help, I'll rate your answer
.edu bryuitra/courses roee_re Question Completion Status: The following process describes the complete combustion reaction of Toluene fuel C7HB (SG 0.866) with air. Liquid fuel (n1) enters the combustion chamber at 200mL/min, where it evaporated into a stream of air (n2) 15% in excess. Complete combustion reaction in which only fraction of the fuel is burned. The combustion products go to a condenser, where the unreacted fuel and water are liquified. The mass flowrate of the fuel in this steam (ma) is 50. The uncondensed gas leaves the condenser at 60 C and 0.5 atm gauge pressure. Calculate the fractional conversion of the fuel Calculate the SCMH of the air entering the combustion chamber Calculate the volumetric flow rate of the gas leaving the condenser (m³/min). a. b. C. ri4 CO2 n3 Fuel ris N2 Fuel ri1 ni4 CO2 nig O2 Combustion nig N2 Condenser air riz Chamber ng O2 ni, H,0 n3 Fuel niz H,0
2. Ferrous iron (Fe2+) must be removed from a steel plant wastewater to meet a pretreatment standard of 106 M. The proposed treatment scheme involves oxidizing the ferrous iron to ferric iron (Fe³+) in a CMFR. The ferric hydroxide precipitate (Fe(OH)3(s)) will be continuously removed from the bottom of the reactor to maintain steady state conditions. Dissolved oxygen will be added to the reactor by bubbling air through the solution. The pH in the reactor will be kept constant by the addition of a well-buffered caustic waste stream from another part of the plant. You are given the following information: Temperature=20 °C Waste stream flow rate Caustic stream flow rate = 1000 L/min = 100 L/min Concentration of Fe²+ in the waste stream=5x10-3 M Volume of reactor-72,500 L Saturation concentration of oxygen at 20 °C = 9.08 mg/L = 2.84x104 M Constant pH in the reactor = 9 Assume that there is no dissolved oxygen in either the waste stream or the caustic stream. The reaction occurs in two…
For the decomposition rate constant of methyl acetoxypropionate (=A) CH3COOCH(CH3)COOCH3(g) → CH3COOH(g) + CH2=CHCOOCH3(g) a value 0.0317 s-1 was found at 610 K. The decomposition is carried out at this temperature in a closed vessel having a volume of 20 dm³. This reactor initially contained 0.4 moles of pure acetoxypropionate. Assuming ideal gas phase behaviour, calculate: a) what will be the composition of the reaction mixture (in mole%) after 90 s from the start of the reaction, b) reactor pressure at this time.
Determination of Total Chlorine Residual Description of the MethodThe chlorination of a public water supply produces several chlorinecontaining species, the combined concentration of which is called the total chlorine residual. Chlorine is present in a variety of chemical states, including the free residual chlorine, which consists of Cl2, HOCl and OCl–, and the combined chlorine residual, which consists of NH2Cl, NHCl2, and NCl3. The total chlorine residual is determined by using the oxidizing power of chlorine to convert I– to I3-. The amount of I3- formed is then determined by titrating with Na2S2O3 using starch as an indicator. Regardless of its form, the total chlorine residual is reported as if Cl2 is the only source of chlorine, and is reported as mg Cl/L. The description here is based on Method 4500-Cl B as published in Standard Methods for the Examination of Water and Wastewater, 20th Ed., American Public Health Association: Washington, D. C., 1998 ProcedureSelect a volume of…
Determination of Total Chlorine Residual Description of the MethodThe chlorination of a public water supply produces several chlorinecontaining species, the combined concentration of which is called the total chlorine residual. Chlorine is present in a variety of chemical states, including the free residual chlorine, which consists of Cl2, HOCl and OCl–, and the combined chlorine residual, which consists of NH2Cl, NHCl2, and NCl3. The total chlorine residual is determined by using the oxidizing power of chlorine to convert I– to I3-. The amount of I3- formed is then determined by titrating with Na2S2O3 using starch as an indicator. Regardless of its form, the total chlorine residual is reported as if Cl2 is the only source of chlorine, and is reported as mg Cl/L. The description here is based on Method 4500-Cl B as published in Standard Methods for the Examination of Water and Wastewater, 20th Ed., American Public Health Association: Washington, D. C., 1998 ProcedureSelect a volume of…