View PoliciesShow Attempt HistoryCurrent Attempt in ProgressX IncorrectAn overhead view of a door is shown. If the compressive force Facting in the coupler arm of the hydraulic door closer is 14 lb with theorientation shown, determine the moment made by this force about the hinge axis O. The moment is positive if counterclockwise andnegative if clockwise.Assume a = 1.625 in., b = 1.500 in., c = 1.000 in., d = 16 in., and 0 = 29°aAnswer: Mo= i 538.74lb-in.

To find the moment about point O -

cempt History Attempt in Progress Incorrect erhead view of a door is shown. If the compressive force Facting in the coupler arm of the hydraulic door closer ation shown, determine the moment made by this force about the hinge axis O. The moment is positive if counte ve if clockwise. he a = 1.625 in., b = 1.500 in., c = 1.000 in., d = 16 in., and 0 = 29° ver: Mo= i 538.74 A d 1 1.0 B F lb-in. OL

cempt History Attempt in Progress Incorrect erhead view of a door is shown. If the compressive force Facting in the coupler arm of the hydraulic door closer ation shown, determine the moment made by this force about the hinge axis O. The moment is positive if counte ve if clockwise. he a = 1.625 in., b = 1.500 in., c = 1.000 in., d = 16 in., and 0 = 29° ver: Mo= i 538.74 A d 1 1.0 B F lb-in. OL

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find P
Q2. Find the magnitude of the moment about BC.
The light right-angle boom which supports the 360-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. A Ox - Answers: IM TAC = i Me C 0.65 m y 1.05 m! 0.65 m 10 B 360 kg 1.30 m 2.30 m N Oy E 1.45 m II D N TBD = 1.45 m Hr x N O₂ = Mi N TBE = i N N
For the quarter circle gate BC with a hinge at C, the force P = . kN to hold the gate stationary for 6 m wide gate. Let r = 3.9 m .... ..... P В r m Water C
The pipe is fixed to wall at A. Calculate and draw the internal forces created at A section of the bracket beam?
2)There is a roller at A and pin support at B. Label the tip of the cantilever "E." The "C" and "D" labels can be disregarded. Use an x-coordinate that starts at the tip of the cantilever and goes to the right. 4 kN/m A B -1.5 m -1.5 m -1.5 m- -1.5m-
For the given retaining wall as shown, determine the following: Note: The water table for the given soil profile is located at an H1 depth below the top of the wall. 9. = 18 kPa %3D Ya = 18 kN/m³ O =25° H = 3 m %3D %3D II, = 4,5 m Yvar= 19.5 kN/m3 %3D o'= 30°
Determine the mass of the heaviest uniform cylinder that can be supported in the position shown without exceeding a stress of 50 MPa in cable BC. Neglect friction and the weight of bar AB. The cross-sectional 6 m area of BC is 100 mm2. 4 in 6 ni-
Please help, I promise to give good feedback. Please do not just guess. Thank you!
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Determine the resultant internal loadings acting on the cross section at C. 600 N/m A. В D |C |-1 m--1 m-1 m ---1.5 m1.5 m 900 N
4. I The gate shown in the figure below is a quarter circle and hinged at point H. Determine the horizontal force per unit width of the gate, P, required to hold the gate in place. Neglect the friction at the hinge and the weight of the gate. 6 ft Water Gate Hinge