1-91. The 60-kg flowerpot is suspended from wires AB and BC. If the wires have a failure normal stress of o fail = 380 MPa, determine the minimum diameter of each wire. Use a factor of safety of 2. AP 60° B Proho 01/02 45°

Q: Date No. A diffevential manometer is connected at two puints A and B of two pipes as Shown on the…

A:

Q: The triangular distributed load acting on the beam can be replaced by a concentrated load of ...…

A:

Q: Determine the following reaction and the TAC

A:

Q: (69 HW A Shaft comssed nf Segments Ac, cD and DB 1S fastened to rigid SurPorts and loeded as shown,…

A: Given; TC=300 NTD=700 N Bronze=25mm diameter Aluminum=50mm diameter Steel=25mm diameter

Q: gitudinal and circumferenti

A: first take a cross section AA ans BB  in the given figure and then analyse the area carefully

Q: w kH m 2.0m PIN 15KNM 15 KN•m 2.0m RAX=24 KN 15KNM C 2.0 Roller. Find the value of w 4m Rc Ray 8m

A:

Q: Ex Determine the required lengthef cord(AC) in figure, so that the (8 ka) lamp can be suspended in…

A:

Q: A beam is fabricated by bending and welding a 6mm thick plate to form a hollow rectangular box…

A: Width of hollow rectangular box=100 mm, Depth of box=160 mm, Thickness(t)=6 mm, Permissible bending…

Q: 7.) A steel tape of a nominal length of 30 m was used to check the distance between two offset pegs…

A: L = 30 mA = 2 mm2 W = 4.5 NE =  200 KN/mm2 or 200,000 N/mm2

Q: The observed temperature when the length of tape is 50 m is 29.6 °C and a pull of 15 kilos IS…

A:

Q: В 6 m 4 m A E F 4 m 3 m 3 m 300 kN 120 kN

A:

Q: Examplel 89 For the frame shown below, the initial displaceme velocity is 13 mm/s. Damping is 10% of…

A:

Q: | %17 elearning.yu.edu.jo a Time left 163:16:23 Question 1 Not yet answered Marked out of 4.00 (CLO…

A: Stress: The total resistance that is offered by the body to the applied load is known as Stress. In…

Q: A line is recorded as 472.90m long. It is measured with a 0.65kg tape which is 30.005m long at 20C…

A:

Q: поор thickness of 0.25 in., and width of 1 in. If it and t meter rigid cylinder have a temperature…

A:

Q: 20kN/m 4m E = 2 *10³ kN/m² I = 1 *10-4 m4 Required: AB Answers in structures lectures: ETABS's…

A:

Q: culate ftop at the ends. (MPa), consider sign convention (- for compression, + f sion) 5 kN/m…

A: Width of Beam = 400mm Depth of Beam = 800mm Moment of Inertia of Beam = BD3/12…

Q: Q.2 For h=1 m in the setup shown in figure find: 1. Pressure head at point a 2. Seepage velocity 3.…

A: Given data: Length of sample (Z) = 1 m h = 1m porosity (n) = 13 hydraulic conductivity (k) = 0.5…

Q: Determine the maximum deflection for the heam chown in the fioure by the conjugate beam method. 120…

A: Given data in question  Simply supported beam Span member length  Load Elasticity modulus  Moment of…

Q: A line was measured with a 30-m steel tape and its measured direction with the use of compass was S…

A: Answer Let us first calculate the sag correction based on the given data. Calculation of Sag…

Q: mpletion Status: Two cables suspending a 100 kg object. The cables are at different angles from the…

A: Given  Weight of block = 100kg  Angles = theta = 35⁰              theta = 42⁰

Q: Solve for the support reaction of the following problem. kindly show your solutions below. thank you

A:

Q: 80 mm 20 mm | 3P glued joint · NA 2 m 2 m 160 mm В 1.0 m 1.0 m -le 20 mm

A:

Q: fluid é 1,500 kglm3 W= IM 8M 5 m Gate7 4M

A:

Q: P -2m -2m D P -2m- -2m E P -2m- 2m

A:

Q: A homogeneous rectangular gate AB 6.1 ft wide and 10 ft long. Friction in the hinge is negligible.…

A: My dear  Given data Width of the gate Length of gate Friction is negligible

Q: The flywheel A rotates clockwise under the action of a 700 N-m couple. A band break is to be used to…

A:

Q: The standard length of a tape is 100m having a weight of 1.2kg with the standard temperature of 20 C…

A: Normal tension occurs when Sag correction is equal to pull correction.

Q: 5 A damped freely vibrating SDOF system weighs 25 kg, spring with stiffness 20 N/mm and damping…

A: Given, SDOF SYSTEM weighs= 25kg Stiffness= 20N/mm Damping ratio= 0.08

Q: Determine the reactions at A and B 600 N/m 900 N•m В D 1 m 1 m 1 m C

A: Given,

Q: • Two forces act on the hook. Determine the magnitude of the resultant force 30 200 N 40 500 N

A:

Q: T00 m steel tape was standar dized 2.1 and supported throughout its whole length and found to bc…

A:

Q: Ex-6. A steel tape with a cross-sectional area of 0.039 cm? and weighing 0.909 kg has a length of…

A: We have to determine the corrected horizontal distance

Q: Prob 2. (15pts) A line was found to be (2865.35+y)m long when measured with a 30-m tape under a…

A: For the given line,

Q: 3. With the transit at point A and the line of sight horizontal, the stadia intercept at B was found…

A: NOTE- Question 3 has been asked to solve. stadia intercept at B, s=1.94 m stadia constant C=0.3…

Q: Ex4:For the beam shown in the fig. blew find the value of (y) ,using the data f'. = 40Mpa.fy =…

A: Given, f'c=40Mpafy=414Mpa6 bars of 25mm diameterDead Load Calculation.D.L=L.L×B×D…

Q: Determine roller support reaction

A: Given data : The value of Point load P=15 KN The value of uniformly distributed load w=25 KN/m…

Q: 3. If the coefficient of static friction at contact points A and B is μs = 0.3, determine the…

A: Step 1:Solution: Step 2: