CD tests were performed for a single, identical soils with three specimens and the result were as follows: (values are in kPa) Test Chamber Pressure Axial Stress at Failure 1 2 50 92 127 100 150 3 166 Q: What is the cohesion of the soil in kPa? Round off your answer to the next whole number.

CD tests were performed for a single, identical soils with three specimens and the result were as follows: (values are in kPa) Test Chamber Pressure Axial Stress at Failure 1 2 50 92 127 100 150 3 166 Q: What is the cohesion of the soil in kPa? Round off your answer to the next whole number.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. A laboratory consolidation test was performed on a cohesive soil specimen with drainage on top and at the bottom. The original height of the specimen was 2.54 cm. Based on the log time versus deformation data, the time to achieve 50% average degree of consolidation was 11 min. Calculate the coefficient of consolidation (in cm²/min) for the soil sample.
Soil mechanics
A clean sandstone core sample with diameter of 3.8 cm and length of 5.6 cm is saturated with a brine. The core was desaturated in several steps, and the resistance was measured at each saturation. The results are as follows: Water Saturation (Fraction) Resistance (kS) 1.000 1.302 0.900 1.695 0.800 2.283 0.730 2.878 0.640 3.775 0.560 5.637 0.480 7.838 0.375 13.175 0.350 17.050 0.300 26 Brine resistivity= 0.74 2m Archie coefficient 1.03 Cementation factor= 2.2147 (1) Estimate the rock porosity. (2) Determine the saturation exponent. (3) Estimate the amount of oil and brine (in cc) in the core sample when resistivity index is 5. All steps of the calculations should be shown.
The following data represent the results obtained from the specific gravity (S.G.) test performed in a soil laboratory including twenty sand samples. The value of mode is 2.65. * Specific Gravity Number of Samples 2.30-2.39 1 2.40-2.49 2.50-2.59 2.60-2.69 2.70-2.79 2.80-2.89 1 47
Q': A- Classification tests have been performed on a soil sample and the grading curve that shown in (Fig. 1) and Atterberg limits obtained. Classify the soil using the USCS? L.L=32 and P.L=26 100 80 60 40 20 Fig. 1 0.1 1 Particle size (mm) 0.0001 0.001 0.01 10 100 % Finer
Q3. A 1200 g sample of Gravel in the SSD condition in air and weighed 770 g when immersed in water. Also, a 500 g sample of Sand in the SSD condition in air and weighed 300 g when immersed in water Calculate the BSG(SSD) of the sand and gravel 1) the BSG (SSD) of the Gravel * 1.2.791 2.4.71 3.3.703 4.2.50 2) the BSG (SSD) of the Sand * 1.2.221 2.3.590 3.2.500 4.3.232 Choose one answer and write the answer number for me
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquid limit of this clay? (Use Interpolation) Group of answer choices 39.85% 39.99% 36.74% 38.63% Please answer this asap for upvote. Thanks
Three samples of Soil were collected during soil exploration for the construction of a Highrise Building. a) Choose the most appropriate Test to determine shear strength parameters for each of the sample described as under i) Saturated Plastic Clay ii) Well Graded Sand iii) Silty Clay b) Draw typical graph between shear stress and normal stress for each of the sample described as above.
An oedometer test is conducted for a soil sample. The sample is consolidated under vertical stress of 50 kPa. The oedometer test finished at 144 min and data are given in table I. The average thickness of the sample is 20 mm. Predict the coefficient of consolidation (cv, in mm^2/min) using Casagrande log t method and Taylor square root of t method. Please use the empty graphical papers.
Problem 1.2.1: The data below were obtained with tension device from two soils of unknown texture. Suction (en) 0 10 20 50 100 300 1000 10,000 20,000 100,000 Water content Soil A Soil B 44 44 43.9 38 22.5 12.5 7 5.2 5.1 4.9 52 52 52 31 48 32 20 13.5 13 128 Answer the following questions: 1. Which soil has a higher porosity? 2. What is the bulk density of the two samples? (Assume that the density of solids comprising both samples is ps = 2.65gm/cm³.) 3. What is estimated water content in the two samples at suction 15cm?