5. A laboratory consolidation test was performed on a cohesive soil specimen with drainage on top and at the bottom. The original height of the specimen was 2.54 cm. Based on the log time versus deformation data, the time to achieve 50% average degree of consolidation was 11 min. Calculate the coefficient of consolidation (in cm²/min) for the soil sample.

5. A laboratory consolidation test was performed on a cohesive soil specimen with drainage on top and at the bottom. The original height of the specimen was 2.54 cm. Based on the log time versus deformation data, the time to achieve 50% average degree of consolidation was 11 min. Calculate the coefficient of consolidation (in cm²/min) for the soil sample.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Laboratory consolidation tests were conducted on a specimen collected from the middle of the clay…

A: The results of the field consolidation curve are interpolated from the laboratory test results.The…

Q: 3- Following are the results of a laboratory consolidation test on a sample of undisturbed clay…

A: Draw the horizontal line from maximum curvature Draw tangent from the maximum curvature point…

Q: A programme of consolidated-undrained triaxial strength tests has been conducted on three soil…

A: We have to determine the valur of appropriate drained strength envelop for the soil according the…

Q: A consolidation test has been performed on a sample obtained from a saturated clay at a point 12m…

A: To determine is the given soil is under consolidated, normally consolidated or over consolidated.…

Q: The results of a standard Proctor test are given in the following table. Given: Mold volume : 1/30…

Q: The consolidation rate data presented in Table 2 (next page) correspond to the 20 to 40 kPa load…

A: Given data: The initial height of the sample, Ho= 25.4 mm Drainage is provided in the both sides of…

Q: A cohesive soil sample is subjected to an unconfined compression test. The sample fails at a…

A: Given:- A cohesive soil sample is subjected to an unconfined compression test The sample fails at a…

Q: The results of a laboratory consolidation test on a clay specimen are the following. Pressure, r…

A: In this question we have asked elong curve and preconsolidation pressure and compression index…

Q: vertical stress at the middle of the clay layer will increase by 132 kPa. Ca consolidation…

Q: A one-dimensional consolidation test was performed on a sample, 0.75-inch high, taken from a field…

A: solution for double drinage d=H/2consider clay sample H=0.75 there fore d=0.75/20=0.375 in we know…

Q: A series of unconsolidated undrained (UU) triaxial compression tests have been performed on two…

Concept explainers

Calculation of Settlement

The vertical displacement of the structural foundation due to the loading from the superstructure is known as settlement. It is due to the reduction of air voids present in the soil. The amount of vertical displacement depends on the bearing capacity of the soil on which the foundation is laid. The effect of the settlement depends on the magnitude of settlement, uniformity, and the structural design of the structure. The maximum allowable settlement for residential and office buildings should be less than 18 mm, for industrial buildings, it is 38 mm and for commercial buildings, it is 25 mm.

Question

**Problem 5**

A laboratory consolidation test was performed on a cohesive soil specimen with drainage on top and at the bottom. The original height of the specimen was 2.54 cm. Based on the log time versus deformation data, the time to achieve 50% average degree of consolidation was 11 min. Calculate the coefficient of consolidation (in cm²/min) for the soil sample.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given data and to determine

VIEW

Solution and Explanation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a sieve analysis test, 95.5% of the sample is passing the 5mm sieve and 5.13% is passing sieve #200, which of the following is correct about this sample: There is no clay in the sample the percent of silt and clay is: 5.13% There is 4.5% Sand and Gravel in the sample 95.5% of the sample is Sand and Silt
A direct shear test is conducted on a 60 mm X 60 mm overconsolidatedclay specimen. The loading was very slow,ensuring that there is no pore water pressure developmentwithin the specimen (i.e., drained loading). The followingdata were recorded.
A clean sandstone core sample with diameter of 3.8 cm and length of 5.6 cm is saturated with a brine. The core was desaturated in several steps, and the resistance was measured at each saturation. The results are as follows: Water Saturation (Fraction) Resistance (kS) 1.000 1.302 0.900 1.695 0.800 2.283 0.730 2.878 0.640 3.775 0.560 5.637 0.480 7.838 0.375 13.175 0.350 17.050 0.300 26 Brine resistivity= 0.74 2m Archie coefficient 1.03 Cementation factor= 2.2147 (1) Estimate the rock porosity. (2) Determine the saturation exponent. (3) Estimate the amount of oil and brine (in cc) in the core sample when resistivity index is 5. All steps of the calculations should be shown.
a) A CU triaxial test was carried out on a silty sand soil sample. The cell pressure was equal to 200 kPa. At failure the deviator stress was equal to 410 kPa and the pore pressure was equal to 73 kPa. i) Assuming that the cohesion intercept is equal to 0, calculate the friction angle of the soil. ii) If the friction angle was equal to 35°, calculate the cohesion intercept of the soil. iii) Calculate the angle of the failure plane relative to the horizontal plane for the soil shear strength parameters in Question 4 a i and 4 a ii.
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the plasticity index of this clay? (Use Interpolation) Group of answer choices 15.74% 18.99% 18.85% 17.63% Please answer this asap for upvote. thanks