Casing is a hollow pipe which gives strength to the wellbore. ____________ happens when stress is at the center of the body of the casing. a. Buckling b. Bending c. Torsion d. Axial Compression

Q: In torsion of circular shafts for deformation, the cross-sections are not distorted in any manner,…

A: To choose: The correct option. Given: Assumption in torsion of circular shaft for deformation. The…

Q: What is section modulus?

A: The section modulus helps to calculate the outermost stress in the beam section. It is numerically…

Q: b) Based in the stuck pipe case in the last page answer the following questions: i. What do you…

A: Question no 1 solved  As it contains multiple questions, if want any specified question to be solved…

Q: A parcel of massmp=2.4 kg is thrown onto a stationary trolley of mass m7 = 9.9 kg, that is free to…

A: The Answer is Below

Q: 11. A rear flange mounted cylinder extends 14 in. under a load of 10,000 Ibf. What size cylinder rod…

A: Given       Mass, m = 10000 lbf                     = 4535 kg Extension, h = 14 in…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: Solution:

Q: What is the proportionality limit? a. Limit up to which the necking begins b. Limit up to which…

A: 1). proportionality limit is that point where stress-strain curve is linear. d. Limit up to which…

Q: An inclined beam having a cross-section of 0.2m by 0.3m supports a downward load as shown in the…

A: Given:Cross-section of the beam, A=0.2 m*0.3 m=0.06 m2 Find:The maximum stress acting normal to the…

Q: Prob. # 3] A 0.453 kg mass is attached to a spring having static deflection of 7.87 mm. Calculate,…

A: Deflection (∆) =7mm To fund natural frequency of system

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: Due to imperfections in manufacturing or specific applicationof the load, a column will never…

A: Under the application of axial load over a column when there is a deflection in the lateral…

Q: 34. Stress is given by the following formula: (choose correct sentences) a. 8 = 4 b. 8 == c. 8=Ex=…

A: Find  Stress is defined as. Types of Cast Iron

Q: Find the width of a heavy-single ply leather belt (8.75 hp/in) transmitting 11 hp at 1800 rpm motor…

A: Given, Heavy - Single ply leather belt Power, p = 11hp; Speed of the motor, N = 1800 RPM cm =0.696…

Q: (b) A block weighing 2000 N is on a rough inclined plane that makes angle of 15° with horizontal.…

A: Given:W=2000 Nθ=15°F=800 N

Q: What are the three most critical materials properties linked to the functional demands of materials…

A: Given:Options are given with properties:

Q: Why are the young modulus not used?

A: Tension in the wire is givenAnd working tensile strength is also gievn

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: A piece of 3 ⁄ 4-inch 5052 aluminum alloy tubing with a wall thickness of 0.070-inch has an inside…

A: Given, Wall thickness, t=0.07 inch

Q: At the beginning of the compression process of an air standard Otto cycle, p1= 1 bar, T1= 300 K. The…

A: Given, P1=1barT1=300KT3=2250KCompression ratio,r=9.8Engine displacement, Vd=2.7L=2.7×10-3m3/s T-S…

Q: What is the reference withdrawal strength for a 0.148 in. diameter plain shank nail with 1.4 in.…

A:

Q: A thermally operated contact mechanism is shown. If heated above the ambient temperature of 20°C…

A:

Q: . Compressive stress can be defined or described 2s an internal force in a material resisting a a…

A: Compressive stress can be described as an internal force in a material resisting a pushing load.…

Q: 16. The feed rate unit on lathe machine is a. Millimeter per second b. Millimeter per stroke…

A: The feed rate unit on lathe machine is millimeter per revolution.

Q: 1. Moment of inertia for a solid sphere of a given volume is hollow spherical shell of the same…

A: Please find the solution below.

Q: What is the cause of shear in a member?

A: Shear Force: Shear force is due to the force that is applied to the member which acts along the…

Q: Fine-grained materials have stress-hardening properties. a. True b. False

A: To be explained :-Effect of fine-grained materials on stress hardening properties

Q: Describe the various types of supports of a column?

A: The different types of supports of a column are a> Fixed support b> Pinned or hinged support…

Q: A kick occurs because the pressure inside the wellbore annulus is higher than formation pressure. a.…

A: The kick formation depend on the pressure gradient in wellbore annulus and formation pressure.

Q: The figure below shows the shaft of an overhang crank subjected to a force P of 3.5kN. The shaft is…

A:

Q: What is the relationship between the ?distance from neutral axis and stress

A: The stress, s, in the element a distance, y, from the neutral axis i s proportional to the…

Q: why is the cylinder longitudinal stress zero at the bottom?

A: This question is based on the concept of thin cylinders from strength of material.

Q: What is the maximum allowable load that can be carried by a (5 in edge) cubical member. If the…

A: Given data,  Sy= 5000 psi,  Fos= 2  L=5 in.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.