Can you write the answer with assembly code using 8051 - AT89S8253 architecture? With the sensor connected to the p3.5 pin on a conveyor, the packaging connected to the p0.4 pin will be activated at every 168 product pass. The Mode0 will be used for the solution. Write the required program code using the interrupt structure.

Q: Write a program that generates TMR0 interrupt signal every 65.5msec. (oscillator frequency is 4MHz)…

A: #include <stdio.h>//header files#include <xc.h> //Device header for the PIC.#define…

Q: Develop an 8051 Assembly Language Program (ALP) using interrupts to do the following: O Receive the…

A: S Step 1: Set baud rate by loading TMOD register with the value 20H, this indicating timer 1 in mode…

Q: A1. A circuit containing

A: In the given question there is miss print the circuit will containing 64k words as it is clear…

Q: 3. Write an instruction sequence to generate a 15 Hz digital waveform with 35% duty cycle using the…

A: In this task, we are given the requirement to generate a 15 Hz digital waveform with a 35% duty…

Q: Write an assembly program that would control the pins of ATMega328P as the following: if (R20 > 0):…

A: Given: Write an assembly program that would control the pins of ATMega328p the following.

Q: 8051 microcontroller C program to toggle only pin P1.3 continuously every 250 ms. Use timer 0, mode…

A: 8051 microcontroller has two independent timer which can be used as timer(to generate…

Q: It is requested to run an interrupt subprogram with rising edge triggering from RB0 port for 16f84…

A: I Have answered this question in step 2.

Q: Write an AVR assembly program for the ATMega32 to generate a time delay of 20 us using Timer 0 with…

A: We need to write an AVR assembly program for the ATMega32 to generate a time delay of 20 us using…

Q: t a LFSR with 4 shift registers with initial condition S3 = 1, S2 = 0, S1 = 0, S0 = 1 and feedbacks…

A: It is defined as a Linear-Feedback Shift Register (LFSR) is a register of bits that performs…

Q: It is desired to configure a PWM Output Pin on an ATmega328P. Write the AVR Assembly code that will…

A: It is desired to configure a PWM Output Pin on an ATmega328P. Write the AVR Assembly code that will…

Q: Use counter 1 of 82C54 interval timer in order to generate a continuous series of pulses which have…

A: Introduction 8086 microprocessor: The Intel 8086 Microprocessor, released in 1980, seems to be an…

Q: H.W. Design the interface circuit that conncet 8 push putton (keypad) with the MP by using…

A: The answer is given in the below step

Q: AM are made of flip

A:

Q: Answer all the questions below , An array of LEDs as connected below, is needed to be accessed by…

A:

Q: 1.You are synthesizing a chip composed of some logic with an average activity factor of 0.1. You are…

A: answer is

Q: Question Write an Assembly code to implement the following flow-chart : Read Port D to R16 If R16<10…

A: .include "m16Adef.inc" .cseg ldi R16,0 out DDRD,R16 ldi R16, 0xff on DDRBO,…

Q: Can we provide a definition on what an Interrupt is? Describe how each sort of gear operates without…

A: Operating system:- The program that oversees and directs a computer's hardware and software…

Q: W Design the interface circuit that make the interface between 8 switch and control 8 LED where the…

A:

Q: int i; for (i=0;i=2){ GPIOD_ODR &=~(1<<(i-2)); } } At each iteration what is LEDS that will be on…

A: According to the question, we have to explain that at each iteration which LED will be ON. In Step 2…

Q: A Pic16F84A microcontroller have to read from two external sensors from RA4 and RA5 in the PORTA,…

A: We need to find the value of TRISA register for the given scenario.

Q: By using 8086 write a code function that use interrupt to show in 7-Sigment the reduction of ( A )…

A: Truth Table for c: Remember that in this truth table, 10 is A, 11 is B, 12 is C, 13 is D, 14 is E,…

Q: Programmable interrupt controller 8259A is capable for handling up to 64 vectored priority…

A: The Intel 8259A Programmable interrupt controller handles eight of the most important CPU…

Q: The arm assembly has different shift functions shifting bits. One set of shift functions belongs to…

A: Logical shift treats the number as a bunch of bits, and shifts in zeros. This is the &gt;&gt;…

Q: VI. A given hardware contains 5 logic blocks that require 20ns, 35ns, 15ns, 50ns and 25ns…

A:

Q: / Use counter 1 of 82C54 interval timer in order to generate a contimmous series HIGH time of 49usec…

A:

Q: function

A: Interrupts: Interrupt is viewed as number of functions. These functions make the process much…

Q: Separate action is required for each Interrupt category. Figure out which Interrupt events occurred…

A: Digital computers respond to software-related events via interrupts. An interrupt condition notifies…

Q: Write an AVR C-program that uses external interrupt INT0 and Timer1 output compare interrupt to…

A: AVR Microcontroller:      Developed by Amtel in the year of 1996.      It is an advanced version of…

Q: 4. Write the equation between the time delay generated by the 8051’s Timer in mode 1 and the initial…

A:

Q: Write the AVR Assembly instructions for a nested loop with 5 instruction cycles in the inner most…

A: An assembly instructions To a nested loop with 5 instruction cycles in the inner most loop Delays…

Q: Please answer the following question using only one 3-bit binary counter with clear input and the…

A: To generate a specific sequence of numbers using a 3-bit binary counter with clear input, a…

Q: sing instruction IN AL, DX to read a byte information from an input port, which register must be…

A: D.  AL register is used to receive tye 8-bits data.

Q: Consider a change to the MIPS multicycle data path that alters the register file so that it has only…

A: Given: Consider a change to the MIPS multicycle data path that alters the register file so that it…

Q: Using timert in CTC mode and interrupts create a 50HZ square wave on pin 5. Use a prescaling of 256…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: A- Explain how the PACA can be set up to measure the duration of a pulse using the gated time…

A: PACA - Pulse AccumulatorIn Gated Time Accumulation Mode the pulse accumulator counts clock cycles…

Q: a PIC assembly program that toggles a LED connected to RC0 every second. In addition to this, a…

A: It is defined as a microcontroller that has many registers for arithmetic and logic operations. The…

Q: To explain the interrupt service routine: Finally, the ISR gives instructions that begin with IRET…

A: If a real-time operating system (RTOS) is utilised, the process might be the same. Like other…

Q: ck cycle. When E = 0, it stops counting and output stays unchanged. clr is clear input. When clr =…

A: SummaryTo generate a specific sequence of numbers using a 3-bit binary counter with clear input, a…

Q: The interrupt service procedure refers to what exactly. In the last instructions for the ISR, RET…

A: Interrupt service routine (ISR): An interrupt service routine (ISR) is a software function that is…

Q: Develop a PIC18F4321 Interrupt based program to measure the power in watt absorbed by a resistor R2…

A: The objective of the question is to develop an interrupt-based program for PIC18F4321 to measure the…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.