Can some please help me to solve this problem while showing all work, formulas, and diagrams. Please and thank you!!!! 2. For diagrams 1 and 2 above, using the Parallelogram Method only (no other methodwill be accepted) do the following:a) Determine the angle a (alpha).b) Determine the angle (phi).c) Draw the force triangle you would be using in the calculations.d) Determine the magnitude of the resultant force.e) Determine the direction ex of the resultant force with respect to the horizontal x-axis.Notes:●●Use the Parallelogram Method only.Round answers to 3 decimal places for forces and 2 decimal places for angles.Diagrams above are not drawn to scale. 2.F₂ = 400 N4530⁰F₁ = 600 N

Answered: Image /qna-images/answer/8c466e01-ea19-49dd-b019-184ae127af1d.jpg

Answered: Can some please help me to solve this…

Engineering

Mechanical Engineering

Can some please help me to solve this problem while showing all work, formulas, and diagrams. Please and thank you!!!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
Please solve carefully , Important.
Statics of Rigid Bodies Note: If you have already answered the problems in this post, kindly ignore it. If not, then answer it. Thank you, Tutor! Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method of Joints" and then solve them with a complete solution. In return, I will give you a good rating. Thank you so much! Note: Please bear in mind to create two problems based on the topic "Method of Joints." Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!
Below is problem MV1 from the course pack. In an earlier assignment, you created a multiview drawing of this part. Model this part with SolidWorks, with each grid spacing equal to one inch. Create a SolidWorks drawing of this part, with Front, Top, and Right Views. Import dimensions from the SolidWorks part file, and place them on the drawing so that they can be easily read. Add a note that all dimensions are inches. Add your personalized title block that you created in Chapter 2 to this drawing. *Important: Save the drawing first as SolidWorks Drawing (filetype *.slddrw) and then as an eDrawing (filetype *.edrw)! You will upload the eDrawing in Blackboard, not the SolidWorks Drawing - the SolidWorks drawing is associated with the part file, I cannot open the sw drawing unless you also send the part file; however, l can open the eDrawing without the part file.
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
Please help show me how drawing will look in isometric drawing.
Table 1: Mechanical behavior of human cadaver tibial bones during pure torsional loads applied with the proximal tibia fixed and the torque applied to the distal tibia until there is bone fracture. Medial condyle Tibial tuberosity- Medial malleolus -Lateral condyle Head of fibula Ti-6Al-4V grade 5 Stainless Steel 316L Region of bone resection -Lateral malleolus L = 365 mm Annealed Annealed Torque at ultimate failure (bone fracture) Displacement (twist angle) at ultimate failure Torsional Stiffness Table 2: Mechanical properties of candidate materials for the rod. Material Process Yield Strength (MPa) 880 220-270 Do = 23 mm Elastic Modulus (GPa) 115 190 d₁ = 14 mm Figure 1: Representative tibia bone showing the resection region (blue arrows) and median length (L). A circular cross section of distal tibia taken at the level of resection) showing the median inner (di) and outer (Do) diameters of the cortical bone. A tibia bone after resection with the proposed metal solid rod (black line)…
Part 2 Set up a spreadsheet solution to this problem. This will require that you derive one formula to express the relationship between the friction coefficient, the spring constant, and the spring compression; and a second formula to find the cost of using different slide and spring types. Set up your spreadsheet as shown below. You can fill in the "Acceptable?" column manually, rather than using a formula. Turn in a copy of your spreadsheet/Matlab work (solve for $) Friction Spring Constant Spring Compression M k 0.1 0.1 0.1 0.2 0.2 0.2 50 100 150 50 100 150 4 Part 3 Your boss has decided to look at a second option. The spring mechanism will be replaced by a drop box. After leaving the slide, the blocks will travel 5 horizontal feet through the air and pass through a hole into the drop box. Using the slide you selected above, determine how far below the slide (h) to place the hole in the drop box. Yo = 5.2017/5 BLADE 2 RAMPE SLIDE 8⁰ SLIDE Acceptable? (Yes or No) $' Cost 51 In DROP…
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
Please solve it complete please don't copy paste