Calculate the order and cut-off frequency of the Butterworth filter that has a 2 dB passband attenuation at a frequency 30 rad/s and at least 15 dB stopband attenuation at 45 rad/s. Plot its magnitude response with all specifications.

Calculate the order and cut-off frequency of the Butterworth filter that has a 2 dB passband attenuation at a frequency 30 rad/s and at least 15 dB stopband attenuation at 45 rad/s. Plot its magnitude response with all specifications.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: ealize an active filter using inverting opamp configuration with zsro at s: -2 and pole at s: -5 and…

A: Zero at s=−2Pole at s=−5Frequency gain of 2.

Q: The analog signal with a bandwidth of 120 kHz is sampled at the Nyquist rate, then quantized at 64…

Q: n=6

Q: Find the current through the resistor at t=0+, and at t=1.25s. The switch is closed at t=0 50V 2092…

A: The general expression of current in RL circuit is given as i(t)=VsR(1-e-t(L/R))vS=supply voltage

Q: Design an RLC bandpass passive fiter iparallel LC) if -5 KHz, C-luF, =1kHz, A) Draw the circuit,…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Problem #1 Design a passive RC low-pass filter with a cutoff frequency of 500 Hz using a 220pF…

A: In this question We need to determine the cut off frequency in rad/s, value of Resistance R, and…

Q: Design the lowest order Butterworth lowpass filter with -1 dB at cut-off frequency 1kHz, an a…

A: According to the question, we need to design the lowest order Butterworth lowpass filter with -1 dB…

Q: The following low pass gilter specifrcations careregoined for a butterworth analog filter design.…

A: It is given that: Passband gain,Gp≥-0.5 dB,Stopband gain,Gs≤-20 dBωp=1000 radsωs=2000 rads

Q: The Band Stop Filter, (BSF) is another type of frequency selective circuit that functions in exactly…

Q: The values of d and X in the given bode curve are as follows: d=100 kHz, X=5.4 The Rf (feedback)…

A: The given magnitude response is shown below.The value of d is kHz and the value of X is .Note: This…

Q: RLC bandpass design： The target is to filter out the square-wave noise from the 120kHz sinsousidal…

A: The given LCR bandpass filter is shown below. We need to determine the transfer function for the…

Q: Use the two circuits given below to design a band-pass active filter (Find the values of R₁, R2, RA,…

A: According to the question, with the help of the circuit given below The gain of the active band…

Q: 2. For a band-pass filter, the range of frequencies between the points on a characteristic curve…

A: Bandwidth: A frequency range within a continuous collection of frequencies is referred to as…

Q: Design the equivalent digital filter for the following analogue filter below. R Vout Vin Given the…

Q: (c) Design a Butterworth equal component high-pass active filter with f-3dB at 1kHz and at 10Hz,…

Q: Find the capacitance values C, needed for a first-order low-pass switched-capacitor filter that has…

Q: Design an active band pass filter with gain 10,

A: Band Pass Filter-It is the filter which passes only the range of frequencies that is specified…

Q: bandreject filter with a lower cutoff frequency of 400 Hz, an uppercutoff frequency of 4000 Hz, and…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Filter is important in a communication system to pass particular frequency components and to reject…

A: To determine the filter order, cutoff frequency, and transfer function of the low pass filter (LPF)…

Q: Use the MATLAB or SciPy function ellipap to find the poles, zeros, and gain for a third-order…

A: The objective of the question is to design a third-order normalized elliptic lowpass filter with…

Q: Design a bandpass filter, using a cascade connection, to give a center frequency of 200 HzHz, a…

A: Fc=200Hz BW=5KHz Bandpass Gain=4 We need to use 200nF cap

Q: For Butterworth Low-Pass Filter response illustrated in Figure below, Determine the order, natural…

A: Butterworth filter is a sort of filter whose recurrence reaction is flat over the passband locale. A…

Q: Please solve the following problem in details-

A: Final answer:

Q: You need an active lowpass filter that has a cutoff frequency of 500 Hz. If the stopband is defined…

A: Active Lowpass filter- A specialized filter which is used to filter low frequency signal and stop…

Q: RCL bandpass filter,

A: Band Pass Filter-It is the filter which passes only the range of frequencies that is specified…

Q: Realize an active filter using non-inverting op-amp configuration with zero at s: -8 and pole at s:…

A: Zero at s=−2Pole at s=−5High Frequency gain of 2.

Q: a. For the active filter circuit shown below, determine an expression for function in terms of R,,…

Q: Find the decimal equivalent of the binary number (1011.011)2

A: Binary numbers are those numbers which have 2 in their base and decimal numbers are those numbers…

Q: Design a second order lowpass filter using Tow-Thomas Biquad with poles at −1,000 ± 8995.03? and DC…

A: We need to design a second-order low pass filter using the Tow-Thomas Biquad with poles at…

Q: Consider the single-amplifier circuit shown below that realizes the second order lowpass filter…

A: The amplifier circuit is given ashere

Q: Given the digital filter with the following difference equation…

Q: nsider the system given below. Let x() and y() be signs with spectra X(f) and F(f), pectively. The…

Q: . Derive the transfer characteristics of the circuit shown below and prove that it is a band pass…

A: The voltage at the inverting terminal is determined by using the voltage divider rule,

Q: Q1. Design a high pass filter with cutoff frequency of 8Khz and pass band gain of 14 dB. Use a 3.9…

A: The high pass filter need to be designed with cutoff frequency and the pass band gain. The standard…

Q: an active high pass filter with a specified. Design break frequency of 100 krad/sec and a Passband…

A: The design specifications of an active high-pass filter are given as:break or corner frequency…

Q: A Butterworth low-pass filter needs to be built with a cutoff frequency of 5kHz. The stopband needs…

Q: (B1) This filter has the narrowest transition band, with an equiripple passband and equiripple…

A: As per Guidelines we are supposed to do First 3 questions when multiple questions are given..so…

Q: Draw the freg uency response of ideal high Pass filter and write its, eguation

A: to draw the frequency response of ideal high pass filter and write its equation

Q: Q.3) Design a second order sallen-key low uss flter with bandwidth 4 KHz. Xe is 3.978K2 and damping…

A: The answer as given below steps:

Q: For the same IIR filter type and specifications: ) if we reduce the transition band (obtain a…

A: i. The order of the filter is inversely proportional to the transition band the reason behind is…

Q: Let R = 150 Ohm and C = 1uF. What is the peak gain offered by this filter? At what frequency does…

Q: 3) a) What is the transfer function H(@)? for the filter? Sketch a plot of H(w). Consider the…

Q: Design an active bandpass filter using a cascade connection by using a 6 μF capacitor to give a…

Q: Problem 4 ,Design a bandpass Butterworth filter with a passband from 200 to 300 Hz with at most 3 dB…

A: The frequency response of the Butterworth Filter approximation function is also often referred to as…

Concept explainers

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.

Question

100%

(b) Calculate the order and cut-off frequency of the Butterworth filter that has a 2 dB
passband attenuation at a frequency 30 rad/s and at least 15 dB stopband attenuation at
45 rad/s.
Plot its magnitude response with all specifications.
(o)
ond out
fE froquonou
leg IIP Dutte..verth filtor uging

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that lets the spectral components pass between the fa=12kHz and fb=16kHz sequences. If you are using a 32-tap FIR filter. What is the value of the central frequency, f0, in Hz of the band that passes the filter? And what is the outline of the frequency response for the filter passes bands?
To the frequency characteristic in the figureDesign the active filter circuit with0.5 uF concentrators in your designuse.
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
Please show the work done.
Considering a first order low pass filter, with a magnitude of 10 dB in the passband and cutoff frequency equal to fc. What is the magnitude value (in dB) at the frequency of 0.1*fc ?
Design an active high pass filter with a specified Passband break frequency of 1.100 rad/sec and a gam equal to 22. use a capacitor Vahe of loont, For these design, Show: ⑥A circuit diagram of final filter design, Label all Components and Indicate the luput and Output Locations. Do not luctude De Power to the op-amp. ⑥The Jw transfer Function For The Filters -D The Passband gan in dB use the tf and bode command In MATLAB a bode Plot for the filter that the Passband to generate Confirming and the break frequency CLabel both 2nd gan Correat A
SOLVE THISSSSSSSSSSSS
i need the answer quickly
a. Find the value of Xc for resonance. b. Determine the total impedance of the circuit at reso- nance. c. Find the magnitude of the current I. d. Calculate the voltages VR, V1, and Vc at resonance. How are V1 and Vc related? How does VR compare to the applied voltage E? e. What is the quality factor of the circuit? Is it a high- or low-Q circuit? f. What is the power dissipated by the circuit at reso- nance? + VR - + V1. ll R = 20 N X = 402 E 100 mV Xc Vc
Design an analog Butterworth filter that attenuates low frequency signal with the following specifications: 1. -0.5dB attenuation at the pass band frequency of 5kHz 2. -10dB stopband attenuation at the frequency of 2.5 kHz.
H.W2: a) Using 0.1 uF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jwo)where wo is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at wg?
Find the normalized frequency that corresponds to a DT filter cut-off of pi/4. What normalized frequency corresponds a cut-off of 500Hz if the sampling frequency is 11,025 Hz?