Design an RLC bandpass passive fiter iparallel LC) if =5 KHz, C-lpF, =1KHz,A) Draw the circuit, laheling the i/p and olp and drive an expression for HaB) Determine the value of R. L, oa,0a and QC) Find V. at enaif vat)= 1 sin(ot).D) Sketch (approximately) the gain and phase shift versus en, indicating e, eki, enaE) Determine the new value of if a load of 1000 is applied to the filter and the sourcehas Rin-10 2

“Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Design an RLC bandpass passive fiter iparallel LC) if -5 KHz, C-luF, =1kHz, A) Draw the circuit, laheling the /p and afp and drive an expression for Ha B) Determine the value of R, L, oa,o2 and Q. C) Find V. at en aif Fat=1 sinfot). D) Sketch (approximately) the gain and phase shift versus en, indicating en, e1, en E) Determine the new value of if a load of 1000 is applied to the filter and the source has Rin=10 0

Design an RLC bandpass passive fiter iparallel LC) if -5 KHz, C-luF, =1kHz, A) Draw the circuit, laheling the /p and afp and drive an expression for Ha B) Determine the value of R, L, oa,o2 and Q. C) Find V. at en aif Fat=1 sinfot). D) Sketch (approximately) the gain and phase shift versus en, indicating en, e1, en E) Determine the new value of if a load of 1000 is applied to the filter and the source has Rin=10 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(please solve by hand)
Circuit Theory
Need help steps would be helpful please and thank you!
Find the frequency gain
These 5 parts are for one question
3rd Class Electronic Circuit Homework (1): Frequency Response Q) Draw and find the equivalent cct, low and high frequency responses, and overall gain (Av)? Hint: Use any value you want for the Rs and RL. Vcc BDc = Bac = 125 Che = 25 pF Che = 10 pF +9 V %3D Rc 220 N C3 V out R1 12 k2 1 µF RL 1 µF Ω Rs R2 4.7 kN RE 100 Ω C2 10 µF Vin
A two-stage active band pass filter (BPF) is shown in Figure Q2. A table of components values is shown in Table Q2. For this BPF: a) Calculate the passband voltage gain in dB and the quality factor Q of each stage. b) Calculate the critical frequencies and bandwidth of the filter. c) Sketch the frequency response of the filter. R RA RA Rc Св Rp RB Figure Q2. RB=1kQ Rc=4700 RD=3300 CB=27NF Table of Component values of the BPF CA=56nF RA=2kQ Table Q2 HHI•
electronic 2 question. please answer as soon as possible.
If vsig is a triangle waveform, determine the maximum amplitude that vsig can have? Showyour calculation.
Use the image below to help answers parts a and b.in an LRC type circuit series the inductive reactance is XL=484 ohms. and I=0.8 amps is the measured current amplitude.A) In the inductor determine the amplitude of the voltage.B)If the LRC circuit is at resonance frequency find the capacitive reactance.
Answer the following wuth illustration and solutions. 1.) A second-order band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 500Hz and below 1.5kHz. Assuming that both the resistor have values of 1kohms, calculate the values of the two capacitors required. Find also the center frequency of the two frequencies. This is the example/guide that might help.
A filter in the form of a series RLC circuit is designed to operate at a resonant frequency of 20kHZ. Included within the filter is a 20 mH inductance and 80 resistance. Determine the bandwidth of the filter. ANS: 63.66 Hz