Filter is important in a communication system to pass particular frequency components and to reject others. Hence in a receiver system, a low pass filter (LPF) is implemented to receive signals with frequency less than 20 rad/s. This filter has stopband frequency of 50 rad/s with maximum stopband gain of 40 dB. (i) Based on the requirement of ripple of 1 dB at passband, compute filter order, n. (ii) Solve the cutoff frequency, we of the filter. (iii) Determine the transfer function, H(s).

Filter is important in a communication system to pass particular frequency components and to reject others. Hence in a receiver system, a low pass filter (LPF) is implemented to receive signals with frequency less than 20 rad/s. This filter has stopband frequency of 50 rad/s with maximum stopband gain of 40 dB. (i) Based on the requirement of ripple of 1 dB at passband, compute filter order, n. (ii) Solve the cutoff frequency, we of the filter. (iii) Determine the transfer function, H(s).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. Prove that , for a radio receiverOutput SNR in dB = Input SNR (dB) - Noise Figure(NF)[You can start the derivation from the relation connecting Noise Figure (NF)and Noise Ratio(F) ] note: the answe will be by hand written.
1. For the circuit in the figure below, obtain the transfer function output voltage / input voltage. Identify the type of filter and determine the corner frequency. Let R1=1000, R2=100N, and L=2mH. R1 + L R2 v,(t) (1)'a 2. *Design a bandpass filter of the form in the figure below, with a lower cutoff frequency of 20.1kHz and upper cutoff requency 20.3kHz. Take R=20KN. Calculate L, Cand Q. L ell v,(1) R
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
H5.
Please show the work done.
SOLVE THISSSSSSSSSSSS
(b) A linear time-invariant (LTI) system is shown in Figure Q1. A signal x(t) = rect(t) is applied at the input of an ideal low pass filter with frequency response H1(@) = rect(o/47). The filtered signal of Y(@) is shown. (i) Illustrate graphically X(@), H1(@), E(@) and F(@). (ii) Determine the type and the specification of the filter transfer function, H2(m) in order to obtain the filtered signal of y(1). E(@) F(@) x(t). H(0) H:(@) y(1) Y(@) cos 10zt -12n -10 10r 12n Figure Q1
A receiver is invented by US engineer Edwin Armstrong, which it converts high frequency to low frequency, all processing takes place at lower frequencies. It offers superior sensitivity, frequency stability and selectivity. With neat block diagram and explain each blocks.
very urgent
a. Find the value of Xc for resonance. b. Determine the total impedance of the circuit at reso- nance. c. Find the magnitude of the current I. d. Calculate the voltages VR, V1, and Vc at resonance. How are V1 and Vc related? How does VR compare to the applied voltage E? e. What is the quality factor of the circuit? Is it a high- or low-Q circuit? f. What is the power dissipated by the circuit at reso- nance? + VR - + V1. ll R = 20 N X = 402 E 100 mV Xc Vc
Find the normalized frequency that corresponds to a DT filter cut-off of pi/4. What normalized frequency corresponds a cut-off of 500Hz if the sampling frequency is 11,025 Hz?
1) How can I calculate cutoff frequency, resonance frequency, bandwidth in a filter? 2) What is their formulas?