5.1: Derive the transfer function of the Sallen-Key lowpass filter shown in Figure 6. C6 H +5V X3 TLO74CN U R12 Vin R13 VDD Vout :C5 Vs -5V/-9V Figure 6. Unity gain Sallen-Key Lowpass filter 5.2: Determine the resonance frequency (fo) and the quality factor (Q) of the filter. "

Q: (For each pair of terms, provide a definition of each and explain their similarities and their…

A:

Q: Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor…

A:

Q: 2- The effect of increasing Vs.

A: By three voltmeter method power factor, cosϕ=VS2-VD2-VR22VDVR load current, I=VDR apparent power,…

Q: uèstion 3 NPN BJT is considered as two diodes their anodes are connected togeth O True False Moving…

A:

Q: The total turn ON time of SCR is 24 . If the sum of delay and spread time is 19 , the rise time of…

A: The solution can be achieved as follows.

Q: 44. What type of electrical component has And which Letter marks its forward conduction turn on…

A: Given IV characteristics which shows both forward and reverse bias condition of the diode. It can be…

Q: Briefly discuss the 10 electrical hazards in the laboratory and give the corresponding the…

A:

Q: Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor…

A:

Q: periment, we calculated and measured using multitester the resistor,voltage and current. Our datas…

A: In an Ohm's law experiment, the goal is to measure the relationship between voltage, current, and…

Q: In the experiment of throwing two hair dice, tet the event c be the sum the of two dice is dice is…

A: Solve the problem

Q: 20. (SP)) (S) performs: a. PUSH S b. РОP D c. None

A: The given instruction is: SP←S

Q: We measure gas pressure at the gas valve in? ja. p.s.i.g. b. p.s.i.a. С. c. Inches of Mercury d.…

A: Measure gas pressure at gas valve in?

Q: What is a Semiconductor? Explain the properties of a Semiconductor such as its physics, etc?…

A: There are various kinds of materials depending on the properties of these materials. In electronics…

Q: Consider an electronic device that monitors the temperature of exhaled air by a patient. The circuit…

A:

Q: For an RTD the relationship between resistance and temperature is a. proportional b. no relation c.…

A: Note :- We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: Please explain the difference (in assumptions and when you use them in practice) between the BIS,…

A: The BIS (Best Interest of Society), SPE (Social Planner's Efficiency), and WSE (Welfare-Social…

Q: If the input voltage Vi is a square signal. What will be the form of the output Voltage? (Write your…

A: - Consider the circuit diagram shown in the given figure.  It represents the circuit for the…

Q: live? A (Who do you) - .B (Where do you) - .C (Are you)- .D

A: The solution is given below The correct option is (b)

Q: The size of a bacteria is 0.25 micrometer. This size is same as ____________. a. 250 nm b. 25nm c.…

A:

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: e nearest integer.

A: Current: I=dqdt Heat: H = I2Rt

Q: Give the drain current equation of JFET.

A: The output characteristic of a JFET is shown in the figure below:

Q: а. j -119

A:

Q: your take on the FSF and what it entails.

A:

Q: What is ohm's law

A: The law was named after German physicist Georg Ohm, who detailed measurements of applied voltage and…

Q: 1.17 Test data from four components are given below. Each test consists of a complete traversal from…

A:

Q: are the main region 3 what enside System verilog simulation in time step?

A: Verilog is Hardware Description language . The memory and array declaration in Verilog is static in…

Q: 6. Peak to peak ripple is defined as a) the difference between zero voltage and maximum b) the…

A: According to question: 6) Peak to peak ripple in terms of voltage is defined as…

Q: Q1. For the circuit given below, find the inputs and outputs Q and Q' after four clock pulses. Write…

A:

Q: Q2. An array of seven LED is used to show the outcome of rolling a die. Design a circuit that…

A:

Q: An electrical component has a reliability of 0.95 over 1,500 hours of normal use (note normal use…

A: Given  Reliability = 0.95  Usage in hours = 1500 Here the electrical component usage indicates it…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.