A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: Vc200V, VBE(sat) = 5 V, IBs = 10 A, VCE(Ssat) = 1 V, Ics = 100 A, tg = 0.5 µs, t, = 1 ps, t, = 4 ps, t; = 3 µs, f, =10= 1 mA. The average losses during the rise time t, are equal to:%3D!!kHz, k = 50 % and ICEOVCE AVccVCE(sat)toff1CtonIcsICEOI t,to18TOSHIBA icIcsICEO1Btyt,Select one:Oa.66.67WO b. 56.67WOc.None of theseOd. 44.67We.33.67W

Given Transistor as switch and waveforms as shown Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: VCC = 200V, VBE(sat) = 5 V, IBS = 10 A, VCE(sat) = 1 V, Ics = 100 A, tg = 0.5 µs, t, 1 us, t, = 4 µs, t = 3 us, f, =10 kHz, k = 50 % and ICEO = 1 mA. The average losses during the rise time t, are equal to: %3D %3D %3D VCE

A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: VCC = 200V, VBE(sat) = 5 V, IBS = 10 A, VCE(sat) = 1 V, Ics = 100 A, tg = 0.5 µs, t, 1 us, t, = 4 µs, t = 3 us, f, =10 kHz, k = 50 % and ICEO = 1 mA. The average losses during the rise time t, are equal to: %3D %3D %3D VCE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Change the MOD-8 counter in Figure to a MOD-16 counter, and connect the MSB to the multiplexer E input. Draw the Z waveform. 1 ΚΩ +Vcc W 13 1₂ lo Eight-input multiplexer 74HC151 SSS 17 $₂ S₁ So MOD-8 CLK- counter •JMM
2. For the following circuit assume r = 8.7 A a. Draw the small signal equivalent circuit. b. Find the input impedance. 16 V 270 2 c. Find output impedance. d. Find the voltage gain. B-110 50 a e. Find the current gain. 2.7 Ti- t
For the circuit below Junction voltage is 0.7V the +ve and -ve peak of the output waveform is +10V Vin 0 -10 V t 41₁ O +4.3,-4.3 O +5.7, -5.7 O +10.7, -10.7 O +7.3, -7.3 R₁ ww 1.0 ΚΩ D₁ 5 V Diodes are IN914. D₂ 5 V * out
9. Compute the bias point of the circuit depicted in Figure Vcc=2.5 V 100 ΚΩ Σ1 ΚΩ KQ₁ + 0.5 V- OVCE=738V and IC=1262A OVCE=0.738V and IC=0.001262A OVCE=0.0738V and IC=0.1262A None of the mentioned. OVCE=0.738mV and IC=1262mA
1. Assume a JFET has the transconductance curve shown in the following figure. a. What is loss? b. What is Vestoff? c. What is the transconductance at a drain current of 2.0 mA? Vas (V) ID (MA) 7.0 6.0 5.0 4.0 3.0 2.0 1.0 -6 -5 -4 -3 -2 -1 0
SIGNAL Mention the function or work of each component in the circuit? + Vcc Rc Rc Cc HH www R₁ Cin HH R₂ www. RE Cc HH CE www R₁ 30 www wwww RE CE OUTPUT
Q3) A sine wave is applied to a differentiator with input voltage 1v peak at 1kHz, the parameters to the differentiator are: Rf =1kn and C=0.33µF, find the output voltage and draw the output waveform?
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
A buck converter operating in continues mode has the following parameters: Imin =0.9 A, Pout 124 W, R=2.6 2, f= 250 Hz, and the average value of the input current = 1.8 A. %3D %3D Find The inductor L in mH.
5) With reference to the circuit diagram given below describe in detail the operation of the circuit diagram with all the applicable waveforms for output voltage, out put current and voltage across the thyristors with alpha=90 degrees Vs = Vm sin wr Vo (a)
92 ۱ ۹:۱ ص Qs= 1107 and Qp= 1041 Qs= 1207 and Qp= 1241 Qs= 1007 and Qp= 1041 Qs= 1107 and Qp= 1141 In the figure shown below we can find output current is equal to.. . if the input voltage is equal to 12 mv 12 kO 12 ka 6 ka No option is correct 10 = 32 uA 10 = 34 uA 10 = 38 uA 10 = 36 uA In the fig. shown below we can find the higher critical frequency due to the input