Calculate the moment of inertia of the shaded area about the x-axis.

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

A: Center of mass: The Center of mass is the point on a body about which it is assumed that the total…

Q: Determine the magnitude of the pin force at A. Assume W - 615 lb, a = 3.2 ft, b - 2.3 ft, r = 9 in.…

A:

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: Given data: ◆ The force applied at the joint D: F = 2140 N ◆ The dimensions of truss: a = 3.3 m, b =…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: Determine the resultant R (single equivalent force) of the three forces acting on the simple truss.…

A:

Q: Suppose that the length of the steel bar is measured by a number of different observers and…

A:

Q: A PVC (k = 0.20 W/m-K) pipe is 2.5 m long and has inner and outer radii of 2.3 cm and 3.3 cm,…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: An angle of 41° is found when a sine bar of the length 190.5 mm is used during the precise angle…

A:

Q: On the part in Q1, show the size and shape of the tolerances zone. Lecture 5 Q1 On the part below,…

A:

Q: How many dimensions on this print express the tolerance using the limit method? (Note:exclude thread…

A: Geometric tolerances allow an acceptable amount of dimensional variation with the maximum available…

Q: A slip gauge setting height  of 65.215mm is observed and an angle of  480 is found during the…

A: Given data, Slip gauge height  (h) = 65.215 mm Angle (€) = 48° Find  Length of sine bar (L)

Q: Dimension the holes & shafts for the required linear tolerance. Also calculate the hole tolerance,…

A: For Hole: For RC3 : RC stand for Running Fit . The nominal diameter is 2.00 in. Hole tolerance is…

Q: 2. Form tolerances are independent of all other Features Size Limits Datums ?

A: Form tolerance is a geometric tolerance that defines the roundness, flatess, straightness of a part.

Q: For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A…

A:

Q: Given the following sentence descriptions of the geometric tolerance information, correctly sketch…

A:

Q: 2. Nominal size is 40mm, the clearance is between 24µm and 92µm, the span of the clearance fit is…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

A: We need to find the center of mass of the system . To find center of mass of system, we have to…

Q: Draw the following graphic symbols (a) Total run-out (b) position tolerance (c) symmetry tolerance

A: Given: Draw the given graphic symbols.

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: The uniform beam has a mass of 41 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: 2. During an isothermal process at 88°F, the pressure on 8 Ibm of air drops from 80 psia to 5 psig.…

A:

Q: Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height…

A: Sine Bar is used to measure taper angle by using gauge lengths and length of sine bar. It is the…

Q: Refer to the figure below. What is the MMC, LMC and geometric tolerance for the Hole and Pin: a.…

A:

Q: A slip gauge setting height 50.14 mm is observed when a sine bar of the length 147.32 mm is used…

A: Slip gauge angle

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 40…

A: Basic size=40mm Tolerance of hole=0.06-0=0.06mm Tolerance of Shaft=-0.015+0.07=0.055(may be the…

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: For an ordinary concrete slab to be laid" -3 within tolerance, engineers can only realistically…

A: Given question is related to metrology and inspection We have to complete the expression that is…

Q: A B D (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what…

A:

Q: state the functions of interference fit and draw it on illustration of size tolerance zone .

A:

Q: Specify a flatness tolerance of .004 for the top surface of the part in the drawing below. A. B. C.…

A:

Q: I need help with numbers 4 and 7. They are both wrong.  One the part attached what is the maximum…

A:

Q: Match the following term to the phrase that describes it. I had this question answered but number 3…

A: Tolerance is the amount variation is permitted to vary from the original dimension.

Q: A shaft has to be assembled with a hole. The shaft has maximum limit 59.762 and minimum limit 59.56,…

A: It is required to calculate tolerance of hole and shaft

Q: The 590-kg uniform I-beam supports the load shown. Determine the reactions at the supports.

A: