calculate the minimum film thickness.

Q: MCQ By ACI-318_19 CODE

A:

Q: Q.1.17 -For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13…

A:

Q: The external and internal diameters of a collar bearing are 200 mm and 150 mm respectively. Between…

A: Given: External diameter, D2 = 200 mm = 0.2 m Internal diameter, D1 = 150 mm = 0.15 m Oil film…

Q: Note: For this question, Reynolds number is not needed, so don't spend time calculating it.…

A: V1 = Q/A1 = 0.015/(3.14*0.14632/4) = 0.8927m/s V2 = Q/A2 = 0.015/(3.14*0.07372/4) = 3.518m/s

Q: The steel bat All has a rectangular cross section (E1) Figure 3m -20 mm 30 mm 20 mm tof 1 Part A it…

A: The load acting at on the column AB through the beam BC is given by (wL/2) = (w x 5 /2…

Q: An oil of viscosity grade ISO VG 32 and standard density is specified for use in an SKF spherical…

A: SKF spherical roller bearings are characterized by their self-aligning ability and high load…

Q: 20kN 1m 4kN F 3 m 2.5 m Rg Rc A.

A: Solution:- We know that At equilibrium, RB+RC=F+4+20 KN According to given condition, when the beam…

Q: DETEA MINE THE Double INTEOrs TIOM METHOD

A:

Q: Q3:-Find the resultant of water and oil on the cylinder which has 3m length. Water

A: Given data Specific gravity  Oil Water Equation of circle from which we got to know that its radius…

Q: Examplel 89 For the frame shown below, the initial displaceme velocity is 13 mm/s. Damping is 10% of…

A:

Q: поор thickness of 0.25 in., and width of 1 in. If it and t meter rigid cylinder have a temperature…

A:

Q: A saturated soil fails under cyl indvical Spaci hen of a a štvess of 150 kPa in an unconfined…

A: Given  Failure plane makes 52° with horizontal  Normal stress at failure = 150 kpa

Q: H-W 2 Given d, =5omm v, = 36 m/s negkcting frichion between jet and plate, find the d oV reattion…

A: H.W2 Introduction to find reaction (force ) : Force between jet and plate is denoted as F  Force F…

Q: Q9 A shaft of diameter 10 cm having a clearance of 1.5 mm rotates at 180 rpm in a bearing which is…

A:

Q: Q) EthaneL at 200CP= 789 Kglm', Mz00012 182/m.s) flow at a horizon tal cast-iren pipe with L 12n 125…

A: To find shear stress and percentage reduction-

Q: DETERMINE THE STRETCH IN SPRING OC To SUPPORT THE SOD Ib LOAD. AUSO DETERNINZ THE TErSION FORLSS IN…

A: To determine the tension in all the cables and the stretch in the spring.   From the given figure,…

Q: From the figure shown which of the following gives the best outside diameter in increments of 2mm. D…

A: Given: D = 875 kN L = 1450 kN Fy = 290 MPa Thickness of the pipe, t = 12 mm Length of the column. L…

Q: - For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s.…

A:

Q: Example Ti.6 For the frame shown below, the initial displaceme velocity is 13 mm/s. Damping is 10%…

A:

Q: For the following assembly consisting of three disks A, B, and C: Determine if the assembly is…

A:

Q: A 500 mm x 500 mm square tied column shown is reinforced with 10 – 28 mm diameter bars with a steel…

A:

Q: mpletion Status: Two cables suspending a 100 kg object. The cables are at different angles from the…

A: Given  Weight of block = 100kg  Angles = theta = 35⁰              theta = 42⁰

Q: - FLUID FLOW IN PIPES I. Proving. SHOW THAT 4. hf= = fLv² 2Dg 128μLQ πρgD4

A: Given: Pipe of length L To find: Headloss in pipe

Q: The distributed load acting on the beam can be replaced by a concentrated load of A acting at A from…

A:

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

A:

Q: Ql:-Answer the following question:- A- A concrete gate with equilateral triangular form have base…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: . A fix inclined-plane thrust bearing is designed to carry a total normal load of  50kN at optimum…

A: As per the given data we have to determine the value of minimum film thickness assuming that the…

Q: A pressure vessel is constructed with an open-ended steel cylinder of diameter 6in

, length 8in

,…

A: Diameter of cylinder, Length of cylinder, Wall thickness, Bolt diameter, To find: Internal pressure.

Q: M, Q5. The pipe is fixed to the ground at point A. It is simultaneously subjected to normal force of…

A: The given data is: Force F=10 KN Bending moment, Mx=1 KN-m Torque, T=2 KN-m Allowable stress…

Q: Use the Distortion Energy Failure Theory to assess the adequacy of this pipe. (OD 114 mm; ID 97 mm,…

A:

Q: operating pressure of 1000 psi. The maximum recommended velocity is 20 ft/s and the factor of safety…

A:

Q: Ex4:For the beam shown in the fig. blew find the value of (y) ,using the data f'. = 40Mpa.fy =…

A: Given, f'c=40Mpafy=414Mpa6 bars of 25mm diameterDead Load Calculation.D.L=L.L×B×D…

Q: A B OE Engineers use several different scales for pressure. Standard atmospheric pressure, which is…

A:

Q: Figure (7a) n= 0.33 - Ft/mini 6 Length (H) 2 4 Air pressure of 3.4 pal 2 10 12 atum Elevalion head…

A:

Q: A cantilever beam shown in Fig, with rectangular section shown. Its carry uniform load wand…

A: Deflection of beam : The state of distortion of a beam from its initial shape due to the work of a…

Q: For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s.…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.