For the following assembly consisting of three disks A, B, and C: Determine if the assembly is strong enough to tolerate P=200 kN applied load. Note: diameter di of the top disk = 22 mm; diameter d2 of the opening = 35 mm; and the largest diameter d3 of the hole in the bottom disk = 28 mm, Note: Obearing allow = 400 MPa and Tallow 100 MPa. B d₁ A dz -d₂- 20 mm 10 mm

For the following assembly consisting of three disks A, B, and C: Determine if the assembly is strong enough to tolerate P=200 kN applied load. Note: diameter di of the top disk = 22 mm; diameter d2 of the opening = 35 mm; and the largest diameter d3 of the hole in the bottom disk = 28 mm, Note: Obearing allow = 400 MPa and Tallow 100 MPa. B d₁ A dz -d₂- 20 mm 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 30 mm as shown in the figure. The length I of member is 3 m. MT R Ri If a G, = 77.2 GPa G, = 27 GPa and torque of M- = 76 kN. m S appirec o rdICE TWISting in the memper Determine the maximum shear stress in the tube
Determine the force in the member CE of the truss shown. It has F1=13 and F2-3 loaded as shown. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. 2.53 m 2.07 m, -5.4 m F2 F1 2.25 m E F 4 m 3 m B)
7000 N 7000 N 1 m- 2 m -1 m- 60° A The cross-section of bar BC is rectangular with 40 mm width and 10 mm thickness. A 20 mm diameter bolt at A and a 15 mm diameter bolt at B are used to form a structure as shown above. Determine: • The normal stress in bar BC. • The shear stress in bolt A and bolt B.
Locate the center of gravity of the volume. The material is homogeneous.
When the temperature is at 31°C, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T(x) = (1.1x? – 12x + 113)°C where x is in meters. If the pipe were unconstrained by the rigid wall, what would its elongation be? For A-36 steel, a = 12(10-6)/°C. 150 mm. 10 mm- Section a - a -6 m
Problem 6.2: The aluminum rod ABC (E=10.1x10° psi) (Figure 6.19), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E=29x10° psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation 28 kips 25 kips A D 12 in. -1.5 in. is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ksi. B - 2.25 in. 18 in. E Figure 6.19
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B2 =D 1.0 m; B;= 0.6 m. Determine the axial load acting on bar B, in kN. 35KN B1 B2 B3 10KN 15KN 30KN A 35 B) 20 C) 10 (D) 5
Situation A (1 - 4) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint . The helical weld makes an angle a = 55° with the longitudinal axis. The vessel has inner radius r= 1.8 m and wall thickness t= 20 mm. The material is steel with modulus E = 200 GPa and Poisson's ratio n= 0.30. The internal pressure p is 800 kPa. Calculate the following quantities for the cylindrical part of the vessel: 1. Calculate the circumferential stress or the cylindrical part of the vessel. А. 72 МPа Helical weld В. 36 МPа С. 24 МPа D. 18 MPa 2. Calculate the longitudinal stress or the cylindrical part of the vessel. А. 18 МPа В. 24 МРа С. 36 МРа D. 72 MPa 3. Calculate the circumferential strain. A. 72 x 106 В. 36 х 10% С. 306 х 10° D. 153 x 10* 4. Calculate the longitudinal strain. А. 72 х 10% В. 36 х 10% С. 306 х 10% D. 153 x 10“
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
The assembly consists of a uniform rod rigidly connected to a uniform cylinder. 1 Properties of Rod: LRod = 3.00 m, = 2.00 kg, Te MRod GRod 12 m Properties of Cylinder: rsphere = 1.25 m, msphere = 20.0 kg, lemer Sphere Scylinder y Drawing not to Scale GRod Assembly Sphere Determine the x-coordinate, x, of the mass center, G, for the assembly above. Assembly а 4.00 m b 4.14 m с 3.43 m d 5.14 m Determine the mass moment of inertia, I6. with respect to an axis PAssembly oriented perpendicular to the page that passes through the mass center, G, for the assembly above. Assembly а 13.8kg-m? c 27.8 kg - m? b 38.3 kg m? d 26.2 kg-m?
2.31 The three symmetrically placed rods support the rigid block of mass M. Before the block was attached, the rods' ends were leveled. If the rods' properties are as listed, find the maximum allowable value of M. (sw is the working stress). ow. 1.2m 1.2m 260mm 180mm Copper
PROBLEM 2 A tri metallic bar is uniformly compressed by an axial force P-12KN applied through a rigid end plate The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter l0mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm E for steel =210Gpa, E for brass = 100GPA and E for copper is 120GPA Calculate the compressive stress of each metal due to force P