A rigid DC switch is attached to the 20 mm radius solid aluminum AB shaft. The forces of P = 3kN in the + y axis direction and F = 4kN in the -z direction were applied to the DC element from the C end. Check the safety of the pipe according to the tresca and Von-mises criteria. Tallow 80MPA, oallow = 160MPA %3D T= 20mm A Im D 100 mm

A rigid DC switch is attached to the 20 mm radius solid aluminum AB shaft. The forces of P = 3kN in the + y axis direction and F = 4kN in the -z direction were applied to the DC element from the C end. Check the safety of the pipe according to the tresca and Von-mises criteria. Tallow 80MPA, oallow = 160MPA %3D T= 20mm A Im D 100 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Do not round off in between your sol. Given the following: b=480mm d=700mm fc’= 30 MPa fy=400MPa Mu= 1430 kN-m Determine As A. Use NSCP 2015, As= _________ sq. Mm B. Use NSCP 2001 As= _________ sa. Mm
Question -10 ASAP
13 and 14 please :) ill thumbs up
Draw influece line for Rvd (Please focus on the solution process) P=1 Hinge P RvD اشا A - 4m a 13 C TMA4 72
Note: Where appropriate, assume that Young's modulus (E) for steel is 200 KN mm-2 and the coefficient of thermal expansion of steel (a) is 0.0000112 per °C. OWN SOLVING AND NOT CHATGPT FOR UPVOTE
In the Cylindrical Cam system, the part attached to the Cam profile is called Select one: O a. Follower O b. Shaft O C Guide O d. Pin
Q1. it's required to determine the diameter of pipe BC
A0.375-in.-diameter steel [E = 30,000 ksi] bolt (1) is placed in a copper tube (2), as shown. The copper [E = 16,000 ksi] tube has an outside diameter of 1.000 in., a wall thickness of 0.12 in., and a length of L= 7.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 24 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 1/24 in. The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly, but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition? Rigid washer Rigid washer Bolt () Tube (2) If the force induced in the bolt by advancing the nut is F1, and force induced in the tube by advancing the nut is F2, what is the relationship between F1 and F2?
Ex4:For the beam shown in the fig. blew find the valne of 0) ,using the data f'.= 40Mpa, fy = 414Mpa , L.L- 24, D.L - (self weight) 57.5mm LI-24ENm d=500mm Solurion:
@ Find the reactions 40kft 8k Ag. Bys- A 4' 3 FBD Final FBD in
ROBLEMS oment boreda-U ors 107 21090000 10 2-28M. A T VX 001 2 k/ft 12 ft Figure 2-86M 210800gmdo da snimissa .re- 2-28. Determine the reaction components for the simple beam of the taugh me ‒‒‒‒‒‒‒‒ Figure 2-81 Figure 2-81. 10 k EB-S onugi ads.90 1919 MIE-S Determine the reaction components for the simple beam of Figure 2-81M. 3 ft B 11 3-S A rea oor tion components 30 kN 3 m 1 m 10 kN/m 6m for for the rigid the Figure 2-81M 40 kN 3 m member in B
Please solve Quickly