An element in pure shear is subjected to stresses Txy =-14 MPa , as shown in the figure.14 MPaUsing Mohr's circle, determine the principal stresses.MPa(f) ơ1 =|(g) 02 =MPа(h) Show all results on sketches of properly oriented elements.Choose the correct sketch.P14 MPа14 MPaА.PO, = 45*7 MPa7 MPaВ.P= 45 P14 MPa10 MPaC.P2= 45P10 MPa14 MPaD.= 45-Select- v

An element in pure shear is subjected to stresses Txy =-14 MPa , as shown in the figure. 14 MPа Using Mohr's circle, determine the principal stresses. MPa |MPa (f) ơ1 = (8) 02 = (h) Show all results on sketches of properly oriented elements. Choose the correct sketch. P 14 MPa 14 MPa A. P • = 45 Pa 7 MPa 7 MPa В. = 45

An element in pure shear is subjected to stresses Txy =-14 MPa , as shown in the figure. 14 MPа Using Mohr's circle, determine the principal stresses. MPa |MPa (f) ơ1 = (8) 02 = (h) Show all results on sketches of properly oriented elements. Choose the correct sketch. P 14 MPa 14 MPa A. P • = 45 Pa 7 MPa 7 MPa В. = 45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two bars are made of polystyrene, which has the stress-strain diagram shown. If the cross-sectional area of bar AB is 975 mm² and BC is 2600 mm², determine the largest force P that can be supported before any member ruptures. Assume that buckling does not occur. Include complete steps with explanations and FBD. 1m baxilno σ (MPa) 175 140 105 70 A 35ptension 0 0.20 -1.2 m P 0.40 compression B 0.60 0.80 € (mm/mm)
Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in whole number I = 100 × 106 mm P kN/m 2. 130 mm A NA- B |= 4P 6 m Poy= 200 mm 2P kN 6 -X= 4m - 4P - GP
The bars of the truss each have a cross-sectional area of 1.92 in². Determine the average normal stress in ksi in member BD due to the loading P = 10 kips. NOTE: use absolute value for Normal stress. The final answer should have 2 decimal places where: L1 =3.8 ft. L2 = 4.3 ft. B L1 D L2 E 0.75 P L2
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28500 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.62 in.² and bar (2) has a cross-sectional area of 0.38 in.². After load P is applied, the strain in bar (1) is found to be 670 μe. Assume L₁=68 in., L₂=94 in., a-35 in., b=39 in., and c-22 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a L2 b C D P
Using the Method of Consistent Deformations (Force Method), determine the Fixed-End Moments (FEM) at the fixed support of each beam shown. Take flexural rigidity, EI, as constant.
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: Using the method of equilibrium, and NOTE: support your answer with sketches and the FBD.
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
Please use Mohr's Circle.
7-3. For the given state of stress shown, determine: (a) the principal stress, and (b) the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine thecorresponding orientation of the element with respect to the element shown, and sketch the results oneach element.
Figure below shows a uniformly tapering bar of rectangular cross-section of length L and thickness t. The width of the bar at one end is b₁ and the width at the other end is b2, where (b₂> b₁). The bar is subjected to an axial force P. The axial deformation due to load P is given by _mm. b₂ PL atE b₁ = 20 mm b₂-40 mm -In () then the value of (a + c) is
Determine the stiffness matrix of the given system and obtain the condensed stiffness matrix at the dynamic DOFs if the dynamic forces applied in-plane translational DOFs. All members are axially rigid. E=30000 MPa; I=8x10⁹ mm4; L= 4000 m. Hint: Evaluate the stiffness matrix applying the unit deformation metod as given example in the figure!!! m m m U3 U₂ U₁ mm. u₁=1 and urest=0 U4 U3 2m) U₂ EI, L (2m) U₁ 2EI, L
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.