Calculate the maximum force in newtons exerted by the blood on an aneurysm, or ballooning, in a major artery, given the maximum blood pressure for this person is 150 mm Hg and the effective area of the aneurysm is 20.0 cm2. Note that this force is great enough to cause further enlargement and subsequently greater force on the ever-thinner vessel wall.

Q: The laminar flow of a Newtonian fluid between parallel plates is illustrated in the below figure.…

A: Consider the laminar flow of a Newtonian fluid flowing between the two plates. The total gap between…

Q: Q2 // The diameter of a pipe at section 1 and 2 are 10 cm and 15 cm respectively. Given velocity of…

A: Given that, The diameter of the pipe at section 1 D1 = 10 cm = 0.1 m The diameter of the pipe at…

Q: For a flow over a flat plate the normalized velocity profile is --² where y is in mm 2 U a)…

A: Answer: a) we know that, Displacement Thickness = δ* = ∫0δ (1- uU) dy  Displacement Thickness = δ* =…

Q: drag force

A:

Q: For a needle floating on the surface of a liquid, the downward force of the needle's weight is…

A: For a needle floating on the surface of a liquid, the downward force of needles weight is balanced…

Q: A particle of equivalent volume diameter 0.3 mm, density 2000 kg/cu m. and sphericity 0.6, falls…

A: The first step is to obtain the dimensional group of Reynolds number and the drag coefficient…

Q: Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0098 m.…

A: Shear stress = ζ =  μ dVdy  where,  μ = Viscosity oif oil = 0.04 Pa-s = 0.04 N. s/m2 Velocity…

Q: As is shown in figure 1, the lower plate moves in the x direction with the velocity of U1, and the…

A:

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: Brine (SG = 1.1) is flowing through a 100-mm ID smooth pipe at a Reynolds number of 48000. The…

A:

Q: A manometer with diameters L and d is used to measure the pressures P1-P2 between two points on the…

A:

Q: Determine the pressure drop across the orifice meter as shown in Example Figure

A: Given,  ρ1 = 1000 kg/m3 d=0.022 m ρf=1100 kg/m3

Q: As flow meters, these devices mechanically divide a fluid stream into discrete, known volumes and…

A:

Q: Unit for mass flow rate and molar flow rate

A: The mass flow rate is defined as the differential mass of the fluid flowing per unit of time. The…

Q: D

A: The flow of Fluid in Pipe

Q: Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0064 m.…

A:

Q: What Is The General Balance Equation?

A: Energy is defined as the ability or capacity to do work. There are various forms of energy, for…

Q: . I change my experiment around a bit, so that it will allow me to change the viscosity of the fluid…

A: a)Reynolds number is given as Re=ρuDμ Where ρ- Density of fluid μ- Dynamic viscosity u- Average…

Q: A fluid with a viscosity of 0.45 g/cm-s between rectangular plates. The velocity of the fluid is…

A: Viscosity of the fluid between parallel plates, μ=0.45 g/cm.s = 0.045 Pa.s The top plate is moving…

Q: What factors influence the drag force experienced by a solid object immersed in a fluid,

A: Drag force significantly influences the behavior of solid objects immersed in fluids.It is the force…

Q: Shear stress of the fluid will be maximum at the a. Wall of the pipe O b. In between center and wall…

A: 1) Answer: a. wall of the pipe Shear stress of the fluid is maximum at the wall because at the wall…

Q: 5.1-2. Frictional Pressure Drop in a Flow of Olive Oil. Calculate the frictional pressure drop in…

A: Olive oil density and viscosity at a given temperature are obtained. The Reynolds number is…

Q: A fluid is placed between two large parallel plates. The distance between the plates is 5 mm. The…

A: a) The momentum flux (or force per unit area) is τfyz=FA=0.5+22.5=1 Pa b) Let V2 be the velocity of…

Q: 2. Shear Stress in Soybean Oil. The distance between the two parallel plates is 0.00914 m and the…

A:

Q: The pressure drop AP over a length L of pipe is assumed to depend on the average velocity V,the…

A: Pressure drop=∆P Length of the pipe=L Average velocity=V The pipe diameter=D The average height of…

Q: The U tube shown is rotated about the left vertical leg at 30 rpm. The pressure at point A is…

A:

Q: With respect to Figure 1.1, consider the two parallel flat surfaces spaced 1 mm apart, with a…

A:

Q: Q3- Calculate the thickness of the boundary layer at a distance of 75 mm from the leading edge of a…

A: velocity of water = 3 m/s.Also flow in the boundary layer is streamline

Q: The medicine in a hypodermic needle should be transferred to the patient. The needle has an inside…

A:

Q: Define shear stress and it’s relation with dVx/dy for a Newtonian fluid

A: Shear stress is an important factor in the study of various types of fluids.

Q: Pressure is expressed as the equivalent O True O False height of a fluid column.

A: Pressure is defined as the ratio of force acting per unit area. P = ForceareaP = mgA

Q: Oil flowing at the rate of 0.001 m³/s through an 8 cm diameter pipe has a kinematic viscosity (U) is…

A: Oil flow rate Q = 0.001 m³/s  Diameter of pipe D = 8 cm = 0.08 m Kinematics viscosity v = 2 × 10-5…

Q: 2. Shear Stress in Soybean Oil. The distance between the two parallel plates is 0.00914 m and the…

A: Newton's law of viscosity equation is used to calculate shear rate. Shear stess is product of…

Q: V, = V, = 7 cm/s d = 30 mm d Liquid of viscosity H = 2 cp Stationary V = 0

A: Here we have to calculate the force on the bottom wall as follows: lets write given values,…

Q: Solve this question using geometry and drawing To steady a sign as it is being lowered, two cables…

A:

Q: True or false: Osmotic pressure can be explained by the difference in fugacities

A: It is to be mentioned whether fugacity difference explains the osmotic pressure or not.