Two men exert forces of P = 50lb and F = 80 lb on the ropes. Determine the moment of each force about A. Which way will the pole rotate, clockwise or counterclockwise? * 6 ft 12 ft

Q: Q2. Use the 1/7 power-law profile and Blasius's correlation for shear stress to compute the drag…

A:

Q: the equivalent length of the exchanger as a complete unit (in terms of 20 mm diameter tube).

A: Consider a heat exchanger of length 12m, 10 close return bends and 15 x 90° elbows connected in…

Q: The force required to slip one layer of a fluid past another with a given velocity is * O Rate of…

A:

Q: ind modulus of elasticity of a brass rod of length 200 mm which is subjected to a tensile stress of…

A:

Q: A single crystal of a metal is oriented for a tensile test such that its slip plane normal makes an…

A: Given,

Q: Shear stress profile for a Newtonian fluid flowing in a circular pipe is O A. Linear В. Parabolic…

A:

Q: How we can calculate friction losses due to changes in velocity and direction in side a conduit

A: Friction losses due to changes in velocity and direction in side a conduit can be calculated as

Q: A box is sitting on an inclined plane. One end of the inclined plane is slowly raised, increasing…

A:

Q: Fraction of water

A: To Answer whether the fraction of water in the underflow stream of thickener is zero

Q: Determine the magnitude of the resultant force (R) acting on the plate and its direction (0)…

A:

Q: 4. Draw the (211) plane on a standard set of x,y,z coordinates.

A: To visualize the (211) plane in a standard set of x, y, z coordinates, we can represent it as a 2D…

Q: a. Define (note: your definition must be based on the closed conduits/pipe flow): 11. Unit weight…

A: We have to define the following unit weight unit gravity yield stress shear rate

Q: Sketch the principle of a hydraulic press.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: A centrifuge bowl is spinning at a constant speed of 2000 rpm. The radius of bowl in cm needed to…

A: Given that N =2000 rpmwe have to find radius of bowl in cm when there is needed to create a force of…

Q: Rate of movement of fluid passing one another. * O surface tension Shear O Rate of shear O Viscosity

A:

Q: A fluid whose apparent viscosity increases with shear rate is termed as the fluid. Viscous…

A: Viscosity is a fluid [property. This property studies liquid motion behavior. The measure of the…

Q: 3-foot-long, 8-inch-diameter cylinder inside a 25.8-inch-diameter tube at 3 feet per second. Fluid…

A: Given data: Length of pipe= 3ft Kinematic viscosity=0.006 ft2/s Constant velocity=3fps  Relative…

Q: Determine diameter of galvanized pipe needed to make the water flow along 180m with flow rate 85L/s…

A: Given data: Length of pipe = 180 m Volumetric flow rate = 85 L/s Head loss = 9 m Kinematic viscosity…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: There is a drop in the bubble with the diameter of 10mm and pressure of 250 KN/m?. If the surface…

A: In fluid mechanics, surface tension is defined as the property of the surface of a liquid allows it…

Q: Determine the hydrostatic force acting on the radial gate if the gate is 40 ft. long (normal to the…

A:

Q: The velocity distribution for laminar flow between parallel plates is given by 2 Umax h where h is…

A:

Q: Laminar flow of a Newtonion fluid ceases to exist, when the Reynolds number exceeds? When the…

A: Laminar flow of a Newtonion fluid ceases to exist, when the Reynolds number exceeds?= for laminar…

Q: A manometer with diameters L and d is used to measure the pressures P1-P2 between two points on the…

A:

Q: The power output of a wind turbine increases with the following EXCEPT:

A: the power output of the turbine increases with the following except. Select suitable currect option

Q: 5. Absolute pressure is measured relative to atmosphere. Tor F

A: Absolute pressure is measured relative to a full vacuum Whereas the pressure that is measured…

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: Baffles increases the fluid velocity on the tube side. True False

A: Baffles are used to direct fluid across the tube bundle and run perpendicularly to the shell.…

Q: Magnitude of the resultant force of the coplanar system

A: We will calculate the magnitude of resultant force of the co-planar system by using Rectangular…

Q: Pascal second is the Unit of Oa. Viscosity O b. Surface tension O c. kinematic viscosity O d. Power

A: b) Surface tension:   SI Unit: N/m CGS Unit: dyne/cm kinematic viscosity (m2 s−1). The English…

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: 5. Rods AC and BC are used to suspend the 200-kg load. If each rod is made of a material for which…

A:

Q: Calculate the net force acting on the cone in Figure 4.69. Im Water 3 m Figure 4.69 System for…

A:

Q: Reynolds analogy is preferred over Chilton-Colburn analogy. O True False Depends on Sh O Only for…

A: Chilton Coulburn analogy is widely successful analogy used for estimating mass transfer…

Q: How much error do you think you will have in the actual end-to-end pressure drop when designing a…

A: This question is based on fluid dynamics We have to analyze the end to end pressure drop while…