Question A and B already answered. I need the answer for C Calculate the early time and the late time for each event, showing them on the diagrambelow.(c)I(16)A(10)(11)G(8)(6)M)J(10),D(5),H(12)K(21)B(14)E(15)KEYN(12)Earlyevent(9)7F(20)timeLateeventtime C(4)А(3)F(5)D(2)H(2)(7B(5)G(6)35E(3)The diagram above is the activity network relating to a building project. The number in bracketson each arc gives the time taken, in days, to complete the activity.(a)Explain the significance of the dotted line from event (2) to event 3(b) Complete the precedence table below.Immediately precedingactivityEventACDEFGH.

Given graph contains many nodes and each node contains early node time and late node time. Each edge…

Calculate the early time and the late time for each event, showing them on the diagram below (c) -.. nua -5 I(16) A(10), (11) G(8) M(9) D(5), H(12) K(21) B(14) E(15) KEY N(12) Early event (9)7 沿 F(20) time Late event time

Calculate the early time and the late time for each event, showing them on the diagram below (c) -.. nua -5 I(16) A(10), (11) G(8) M(9) D(5), H(12) K(21) B(14) E(15) KEY N(12) Early event (9)7 沿 F(20) time Late event time

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

SIMULINK Implementation 1. Using SIMU LINK, set up the negative feedback system of (6) above. Plot on one graph the error signal of the system for an input of 5u(t) and K = 50,500, 1000, and 5000. Repeut for inputs of 5tu(t) and 5t²u(t). Use simulation time not less than 50 seconds for all the simulations 2. Using SIMULINK, set up the negative feedback system of (7) above. Plot on one graph the error signal of the system for an input of Su(t) and K = 50,500, 1000, and 5000. Repeat for inputs of 5tu(t) and 5tu(t). Use simulation time not less than 50 seconds for all the simulations 3. Using Simulink, set up the negative feedback system of (8) above. Plot on one graph the error signal of the system for an input of 5u(t) and K = 200, 400,800, and 1000. Repeat for inputs of 5tu(t) and 5t²u(t). Use simulation time not less than 50 seconds for all the simulations Postlab 1. Use your plots from Labs I and compare the expected steady-state errors to those calculated in the Prelab. Explain the…
The voltage Vc (t) (in V) and the current i(t) (in Amp) after closing the switch in the circuit shown in Figure Q2 are given by: -v, (1 -e+) i(t) Vc (t) = V. (1 – e' Vo e R ic(t) T = RC where R = Resistance C = Capacitance Figure Q2 T = Time constant Consider the case where Vo = 30 V, R = 2000 N, and C = 3000 µF b) Assemble your user-defined function with necessary MATLAB code to obtain V, and ic when t = 20 s.
For the truth table attached, create a K-Map and determine the minimum AND-OR expression for it.Your answer is only the minimum expression. (i.e. Do not attach the K-Map)
please help ASAP
Evaluate the DFT for the sequence x(n) = [ 0 , 1 , 1 , 0 ] , where n > 0, then draw the magnitude and the phase for X(K).
Simulation using LOGISM: F(x,y,w,z) =∑m (0,1,2,3,4,6,11,14)
$ Figure Q2 For the truth table shown in Table Q3: a. Find the logic functions of Z₁ and Z2 using K Map Implement using PLA b. Table Q3 $ # & Z₁ Z₂ 0 0 0 1 1 0 0 1 1 0 0 1 0 1 1 0 1 1 0 1 1 0 0 0 1 1 0 1 1 1 1 1 0 1 1 1 1 1 1 0
A voltmeter with an internal resistance of 100 KQ is used to measure the voltage Vab in the circuit shown below, what is the voltmeter reading? 36v R1-12 KQ M 30 18 mA R2=60 kQ R3=15 ΚΩ M + Vab Note: All students are welcomed to solve it, however assignments are mandatory for old students only.
Edit the diagrams, need drawings on it.
Vibrations Question A building is modeled and subjected to ground motion such as a 4.5 magnitude earthquake as shown below. The building is modeled as a single–degree–of–freedom (SDOF) mass–spring system where the building mass is lumped atop of two beams used to model the walls of the building in bending. Assume the ground motion is modeled as having amplitude of 0.2 m at a frequency of 8.5 rad/s, the building mass is 150000 kg, and the stiffness of each wall is 4.519 x 10^6 N/m. r=1.095 wn=7.762rad/s mx''(t)+2kx(t)=0.2cos(8.5*t) Explain if the building will break after the earth quake. Give steps to use MATLAB to obtain the vibratory response due to the earthquake when the building is in bending relative to ground for 0 ≤ t ≤ 25s. Assume zero initial conditions.
using MATLAB plot the following functions together with reference to x where x ranges between 0 to 2π with an interval of π/200. y1 = 2 cos(x) y2 = cos(x) y3 = ¹2 cos(x) Make sure to set the proper labels, title and legend for your graph and mark the graph with blue, solid line with 'x' used as marker. Also, put the proper limits for your axis.
Last step in addition to the previous 2 questions: a lengthy derivation using phasors that the first diffraction peak should have an intensity of I1 ≈ 0.045 I0. Using the equation provided below in the pictures and the statement that β = 1.5π, you can find out what θ value to choose. You can also go for the midpoint between the first two destructive interference locations m = 1, 2 in the equation provided in the last question in which I will provide in the second image here. Repeat your three-path amplitude calculations for this value of θ, and observe what the relative intensity is for the first side maximum according to your calculation. Also explain How do the results improved when subdividing the aperture with 5, or 7, or more paths?