The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200GPa. Calculate its factor of safety for the piston rod?

The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200GPa. Calculate its factor of safety for the piston rod?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

Show all working explaining detailly each step.
In the position shown for the log hoist, booms ACDF and EFG are perpendicular and EFG is parallel to AB. What is the maximum weight (in Ib) of the log if hydraulic cylinders BC and support a maximum of 4123 Ib and 9123 Ib, respectively? Note that BC is a duplicate cylinder. (Hint: Recall multiple failure criteria.) E DE can 12' 10 This is nor your own propèrty so do ngi uwe at n ghi way as if it were your own. Legend: '- foot “- inch A 45° B This is not were your e ownprop 12" o do not use it in way as 12" 24"
A railroad car and its cargo have a total weight of 50 kips. The car is sup 5-50 ported on eight wheels, each of which has a diameter of 25 in. If the co cient of rolling resistance is 0.015 in. between the wheels and the trach and the wheels share the load equally, determine the magnitude of the ho izontal force required to overcome the rolling resistance of the wheels.
Find the greatest weight that can be applied without the front wheels lifting off the ground. The answer is 30,043.43 N show solution
three (3) different cylinder mude from Steel, Aliminurn and Uronze are jointed Logether to torma composite structure and fixed to vall suport. Three (3) axial forces acted on the structure as shown. The fallowing valuc was alroady cietermined: 1 KN to the nght -3kN Tensioa -2 kN compression Reaction al A Internal force for Aluminum Interral force for Brone Este= 200 GPa; Ealumin 70 GPa Egmee 83 GPa Determine Ue eiongalion (A) for ach section: Steel Aluminum Bronve Aluminum A= 400 mm Bronze A-200 mm Steel A S00 m 2P 4P SP 2.5 m 2.0 m 1.5 m
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
The piston rod of diameter 20 mm and length 700 mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200 GPa. The factor of safety for the piston rod is
Find the thickness of a metal needed of the semi-spherical end of cylinder vessel 0.70 meter in diameter to an internal pressure of 2.70 N/mm2. The material is mild steel and tensile is 69 N/mm2
The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15 mm. This spring, having 10 active coils has the ends in plain ground, and has a free length of 200 mm. 1. Determine the length (in mm) at which this spring must be initially compressed to hold a pressure of 1400 kPa applied on a 32-mm diameter valve seat. Use a modulus of rigidity of 80 GPa. 2. calculate the spring’s maximum stress induced if it is compressed to its solid length
Solve the problem:
A 1.7 m diameter closed cylinder 2.7 m. high is completely filled with glycerin SG is 1.65 under the pressure of 230.25 kPa at the top. The steel plates which form the cylinder are 16 mm thick and can withstand allowable tensile stress of 82300 kPa. Compute the maximum pressure at the bottom of the tank to resist hoop tension if it is rotated about its vertical axis. 01594.18 kPa 01549.18 kPa 01459.81 kPa ONone of These O1495.81 kPa