Determine the magnitude of angular momentum of a 2 kg spherical particle about point O as shown in the diagram below. Only enter the value in the answer box in units of kgm/s² 7 m/s 45⁰ Q.... 12 m 2 kg 5 m X

Q: answer is 900.8 please resolve

A: Given Data

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: Please check for the question, verify it is correct or not?

A: There is a half cylinder with length L and radius r.Incoming air velocity is uCoefficient of the…

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: What is the value of w and y? y W 6V2

A:

Q: Please make draw the right-side view, front view, and top view of the given isometric drawing.…

A:

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: _1. He is an English man credited for the invention of a screw cutting lathe. _2. A man from New…

A: Identification test :

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: Subject Date : الموافق 2x92-0 م 24 find divgrad df) 2 19 - موضوع التاريخ

A:

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Read the following statement and choose the most appropriate answers. Statement 1 For a measuring…

A: Accuracy is defined as how close is the measured value to the true value.

Q: 2. A composite furnace wall is made up of a 14 in. lining of magnetite refractory brick, a 5.3 in.…

A: Given data as per the question The thickness of brick =14 in The thickness of magnesia =5.3 in The…

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Q: There are several failure modes by which gears can fail. Select the true statement from among the…

A:

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: The question is not answer fully. Please answer the second part of the question statement.

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: Write legibly and box the final answer

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.