The factor of safety for the piston rod is

Q: Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts

A: Camshaft Camshaft is the shaft at which many cams are connected and it operates with the crankshaft.…

Q: Question: To install the front cover on an engine, position its either on the or on the cover…

A: A gasket is a flat rubber piece that fills the space between two metal surfaces in the engine or…

Q: introduction about Control of Pneumatic Cylinder with AND and OR Functions

A: Pneumatic cylinders (also known as air cylinders) are mechanical devices that generate force in a…

Q: Is a hook good on a compression spring launcher trigger mechanism

A: Given Spring triggered mechanism To find Verify hook is good for spring triggered mechanism

Q: discussion of the temperature distribution problem along rod

A: We will use the fin analogy , a cylindrical is heated at the base and cooled by convection , had…

Q: Compression takes place on both sides of the piston in two cylinders is known as a. single stage…

A: Here, whenever a single cylinder is used and compression takes place on both sides of cylinder. Then…

Q: The shaft in the front wheel of bike is_

A: Given data To select the correct opton.

Q: i. Describe the operation when valves 1 and 2 are in the positions as shown. ii. What would happen…

A: The  two way valves is  fill and drain a vessel is given.

Q: The force applied on the spanner handle while closing a nut generates a ___________   Select…

A: The force applied on the spanner handle while closing a nut generates a ___________ Answer: Moment

Q: aw the pheumatic and ladder dlagram of the given sequence below. Use double-acting cylinder…

A:

Q: what is the minnimum proof strength mpa for M14x2 hex bolt

A:

Q: Why must a cylinder ridge be removed before attempting to remove the piston?

A: Cylinder ridge reamer is a component use to remove the ridge.

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: The rotary compressor gets its name from the fact that it has an off-center piston of rotor which…

A: This question is based on the concept of conpressors.

Q: Hydraulic maintenance is done to prevent

A: Prevention is better than cure. Maintenance activities are done to ensure that no breakdown occurs(…

Q: explain in a detailed manner how a bike start running when kick to the lever rod

A: Kickstarting is used to start an internal combustion engine, typically a motorcycle, by pushing…

Q: Discuss the method of obtaining pressure crank angle diagram. List down the parameters that can…

A: In present day motor showing frameworks the prompt place of the driving not really settled with the…

Q: Is there vibration experienced by the helicopter? i. If yes, what caused it and how to reduce this…

A: Given data:Rotor blade resonant frequency - 6.7 HzFlutter speed - 28 m/sEngine output shaft speed -…

Q: For automobile engines, opening and closing of valves is operated by O a. flywheel mechanism b. cam…

A: The opening and closing of the valves are to be done at a particular timing in the IC engines.

Q: Draw the graphic symbol for a two-position spring centered valve, a spring offset valve, an…

A: Valve symbols are used to develop hydraulic circuits with ease. They convey the necessary…

Q: Determine whether the mechanism below is mandatory movement.

A: The mechanism is shown below, From the mechanism, Total number of link=6 Total number of lower…

Q: While discussing the different types of pressureplates: Technician A says that coil spring types…

A: Option D is the correct naswer

Q: Give examples of calculation turning moment (torque) on the crankshaft piston

A: given data; Give examples of calculation turning moment (torque) on the crankshaft piston.

Q: Find tension in AC and W?

A: Consider the diagram shown below for the given system.

Q: )What are the fuctions of engine camshaft and cranck shaft.

A: Function of Engine camshaft- A camshaft is located inside the cylinder head of the engine. Its main…

Q: describes the angular positions in terms of crank angle position in reationship with the

A: Given data To describes the relationship between angular position of crank and position of piston.

Q: Tech a says that the push on the piston top during the power stroke is transferred to the crank…

A: Tech a is correct.

Q: Task 5 - Brake Callipers and Discs Brake callipers and discs, like the braking system are different…

A: given; (1) examine the example caliper  and examine the material used? (2) How many piston are used…

Q: Please name two type of locking nut, and explain how they function.

A:

Q: the torque required to prod

A:

Q: Number of times the intake valve opens in a single-cylinder four-stroke cycle after completing 200…

A: Given:- Single Cylinder  Four stroke cycle Number of revolution = 200  To Find:- Number of times the…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: From the following identify a false statement regarding the adjustment of drive belt tension for…

A: Use a ruler to find the midway point on the belt's longest run between pulleys. Hold the belt…

Q: What should be done to remove rust, corrosion, pitting, and scratches from the piston bore?

A: PISTON BORE The bore (or cylindrical bore) in a piston engine is each cylinder's diameter. It is…

Q: Define the term in theory of macines Meyer's expansion valve

A: The Meyer's expansion valve consists of two valve known as  main valve and expansion valve which are…

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: Define Braking loads

A: Braking load/force  is the  frictional force that cats tangentially  between the brake pads and…

Q: What do u mean by the factor of safety 3,4....n?

A: Factor of safetyit is the ratio of the ultimate strength of a member to the actual working stress or…

Q: what is the formula for working out spring constant?

A: Spring constant is generally defined as the force per unit elongation.

Q: 5. F = x²i+ czj- yk If the force is conservative, the value of the constant c is O A OB O C O D OE…

A: To find: The value of constant c. Given: The force is F=x2i+czj-yk. The force is conservative.…

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.