C1 (ii). Three lIdentical capacitors are connected in star to 415 Volts, F = 50 Hz, 3 phase supply. If the line current is 12 A. Calculate its reactance and capacitance value.

Q: could you please help me with item d please

A: Asked to find (d) The inductor current position with respective to inductor voltage? And what angle…

Q: In STEP 4, you charged the capacitor completely with the PSB set to 3.3V. Then you set the PSB to 5V…

A: Given Initially capacitor charged to 3.3v with PSB set to 3.3v After sometime PSB is set to 5v then…

Q: Convert hexadecimal to octadecimal A13C

A: Conversion from hexa to octal is not direct, there is steps need to be followed, such as: Change…

Q: What can you determine about the circuit being tested based on what is displayed on the DMM?

A: Circuit shows three lamps, dome lamp, Lamp A and Lamp B are  connected in parallel and supplied…

Q: Question 7 Semiconductors has number of valence electrons.

A:

Q: 2. Determine the combined resistance of three resistors 3.0, 5.00, and 6.0 connected in parallel. 2

A: Here given that three resistance are connected in parallel  R1= 3ohm R2= 5ohm R3= 6ohm

Q: Calculate the voltage across R2 when the voltage drop across the diodes is 0.3 Vdc. CR1 CR2 Vs 1. R3…

A: The problem is based on analog electronics. Below is the explaination:-

Q: A RTD made up of platinum has a=0.00385 and has a initial resistance of 100. Find the value of…

A: Given,

Q: In an energy meter, creep speed is the speed of the aluminium disc's at O a. Full load condition O…

A: In the energy meter,  Creep speed is the speed of the aluminum disc's at

Q: LASCR or light-activated SCR: What is the required in the circuit below to turn off the LASCR and…

A: The LASCR operates on the photoconduction principle, which is conduction caused by a photon…

Q: Prove that the maximum efficiency occurs when the iron losses are equal to the copper losses…

A: To Prove: Maximum efficiency occurs at, Iron loss = Copper loss Considering the current as a…

Q: %3D %3D Calculate the indicated voltage and current, where V, = 5V. The voltage gain, A= 10*. 4ke…

A: Since you have posted a question with multiple sub parts , we will solve first three sub parts for…

Q: 3. Draw the input and output waveform for the following clamper circuits if input signal is square…

A: Given data: frequency f =1 KHZ =103 HZ Peak to peak square wave v = 10 V The given circuit is shown…

Q: the amount of current that the circuit breaker can interrupt without damaging itself electrically…

A: Short circuit limit of CB :- It is the ability of the circuit breaker to withstand 85% to 90% of…

Q: I am confused on current drawn by R2, also power dissipated by R2

A:

Q: (ii) Analyze the output response of Q as shown in the Figure Q3(b)(ii), if it has an positive going…

A: In this question,  Analyze the output response of the JK flip flop.  Assume it work on positive…

Q: 2B/ Al has energy gap of 0 ev, AIN has energy gap of 6.3 ev, GaSi has energy gap of 1.95 ev Classify…

A:

Q: Table 3 6. Plot the values from Table 2 and Table 3 on the same graph done in step 3. Does the diode…

A: Diode is device which is made of semiconductor, basically it act as switch

Q: в1. What do you mean by static characteristics? Explain any one of the static characteristics. B2. A…

A:

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: One of the following elements can be used to make P-type semico Phosphor(P) Arsenic(As) Antimony(Sb)…

A: For p-type materials we need elements having three valence electrons.

Q: Determine the Vdc level across R1 if the diode is Silicon diode

A:

Q: 1. The reverse bias diodes a. D1 only b. D2 only c. Everything d. None 2. The close circuit is a. R1…

A: Given data, Circuit diagram is given as,

Q: Determine the voltage and current meter indications in each circuit.

A:

Q: C₁ = 15 µF V C C₁= 8 µF * V₂20 V

A:

Q: 3. Using constant voltage drop model of V₁ = 0.7V, calculate the current I, the voltage V, and the…

A: A diode is a two-terminal electronic component that allows current to flow in only one direction…

Q: The minimum value of current at which the fuse element melts is called

A: The explanation is as follows.

Q: 10V 1A 4A Ib 122 + 8V Figure Q1(b)

A:

Q: types of electrodes in electric welding

A: Electrodes are used in order to join two metal pieces together by conducting the current through…

Q: Calculate the minimum main protection for 6 A/C air conditioners, their main conductors and the…

A: Step 1:

Q: There are three types of defects which are Point defects, Line defects and Surface defects. Briefly…

A: Crystalline defect, imperfection in the normal geometric arrangement of atoms in a solid crystal…

Q: 13. For the following circuit, the diodes are silicon with a forward barrier voltage of 0.7-V.…

A:

Q: Q1. Two diodes with Isl=10mA and Is2=20mA are used for the total reverse voltage barrier VR=1983V.…

A:

Q: A bank of nickel-cadmium cells is used as the emergency lighting supply for a hospital. There are…

A: When batteries or cells are connected in series, their voltages add and their current capacities…

Q: germanium A compensated semiconductor at T = 300 K is doped with N₂ = 2 X 1012 cm-³ and N = 8 X 1013…

A: According to the question, we need to calculate the thermal equilibrium electron and hole…

Q: Represent the following using circuit of switches :

A: For the given logic circuit the equivalent switch based circuit need to be designed.

Q: The Insulator has a very small energy gap ? True O False O

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.