(c) Refer to Figure 3(c) and assuming that D = 240 mm, w = 66 mm, I = 700 mm, d = 3.5 mm, v = 0.65 m/min, and N = 300 rpm. The cutter has 8 inserts, and the workpiece material is a high-strength aluminum alloy. Calculate: (i) (ii) (iii) feed per tooth material-removal rate cutting time Workpiece Workpiece Cutter Cutter Machined surface Figure 3(c)

(c) Refer to Figure 3(c) and assuming that D = 240 mm, w = 66 mm, I = 700 mm, d = 3.5 mm, v = 0.65 m/min, and N = 300 rpm. The cutter has 8 inserts, and the workpiece material is a high-strength aluminum alloy. Calculate: (i) (ii) (iii) feed per tooth material-removal rate cutting time Workpiece Workpiece Cutter Cutter Machined surface Figure 3(c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to cut a workpiece of 85 x 42 x 8 cm into two equal parts. The milling cutter is 180 mm in diameter and has eight teeth. Cutting speed = 60 m/min, chip load = 0.35 mm/ tooth, and depth of cut = 2 mm, given that the setup and machine settings provide an approach distance of 7mm before actual cutting begins and an overtravel distance of 20 mm after actual cutting has finished, and the return time is a 4-second for idle pass stroke. Determine:- 1. What is the total machining time required for the entire workpiece? 2. The maximum metal removal rate during cutting.
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm, and depth of cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?
In a straight turning operations the diameter of a workpiece is reduced from 50 mm 40 mm using a feed rate of 0.1 mm/rev. The cutting tool used for the process has a normal working rake angle of 15°, clearance angle of 4° and a lead angle of 90°. The cutting force of 1200N and a thrust force of 660 N is measured during cutting operations. The workpiece material was stainless steel with a density of 7850 Kg/m³, thermal conductivity is 15 J/smK, specific heat is 480 J/kgK. The width of the secondary deformation zone divided by the chip thickness wo is assumed to be 0.2 for the above mentioned cutting conditions. The chip/tool contact length is measured as 1.5 mm. (a) Calculate the temperature rise in the primary deformation zone (b) Calculate the temperature rise in the secondary deformation zone (c) Calculate the maximum temperature if the room temperature is 24°C If the tool life for the average cutting velocity of 90 m/min is measured as 10 min. and for a cutting velocity of 160 m/min…
A part surface is machined using single point cutting tool with feed rate of 0.3 mm/ rev. Given that, surface roughness is measured using centre line average method and details were given below, Sampling length = 0.8 mm Vertical Magnification = 10000 Horizontal Magnification = 100 Sum of areas above & below = 960 mm? What will be the Nose radius of cutting tool?
(b) A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4 W.s/mm³) is being reduced in diameter to 17 mm by turning on a lathe machine. The spindle rotates at N = 700 rpm, and the tool is traveling at an axial speed of 300 mm/min. Calculate: (i) (ii) (iii) (iv) (v) cutting speed material removal rate cutting time power dissipated cutting force
6
In a turning operation, the workpiece diameter is Dm=44.00 mm and the diameter after the operation should be 22.00 mm. The cutting speed is set to 105.00 m/min and the federate is 0.03 mm/rev. Calculate the material 3 removal rate (Cm²Imin) for this operation (Do not input units). Your Answer: Answer
Problem 2. (Determining Cutting Speeds in Machining Economics) A turning operation is performed with HSS tooling on mild steel, with Taylor tool life parameters n = 0.12, C = 60 m/min. Work part length = 450 mm and diameter = 80 mm. Feed = 0.20 mm/rev. Handling time per piece = 4.0 min, and tool change time = 1.5 min. Cost of machine and operator = $27/hr, and tooling cost = $2 per cutting edge. Find the a. cutting speed for maximum production rate and b. cutting speed for minimum cost Problem 3. (Production Rate and Cost in Machining Economics) For the two cutting speeds computed in problem 2, determine: the hourly production rate and a. b. the cost per piece.