©4Two 200x75x25.3 channels, back to back, as shown below, act as column of length 5mwith pinned ends. Yield stress =250MPa, E=210GPa.[コロa(a) Use the formula with a buckling load of 100kN and calculate the maximum value ofthe clear spacing a between the channels. (35mm)(b) Use the Perry-Robertson formula given below to calculate the safe load the columncan carry. Take the load factor=1.7 and a=120mmK.f₂=fy+(1+n)ƒe_[(fy20.5+(1+n)fe22= {yle](771.9kN)

The objective of the question is to calculate the maximum value of the clear spacing between the…

Answered: © 4Two 200x75x25.3 channels, back to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Vc,Mc,Nd,Vd,Md
The beam supports the triangular distributed load shown below with Wmax = 900 lb/ft. The reactions at A and B are vertical. (Figure 1) Figure AT PORCE 6 ft D 6 ft C 6 ft W IB TODAY E 4.5 ft 4.5 ft Part A Determine the magnitude of the resultant internal normal force on the cross section at point D. Express your answer in kilopounds to three significant figures. ND= Submit Part B Vp= Submit Part C ΠΙΑΣΦΗΜ Mp= Avec Submit Request Answer Determine the magnitude of the resultant internal shear force on the cross section at point D. Express your answer in kilopounds to three significant figures. ΠΙΑΣΦΩΤ Request Answer n Request Answer vec 1 → C vec S S ? Determine the magnitude of the resultant internal bending moment on the cross section at point D. Express your answer in kilopound-feet to three significant figures. [Γ]ΑΣΦ [4 O I ? kip ? kip kip.ft
L = 0.3m A = 20 x 6 mm E= 70 GPa allowable stress = 120 MPa 0.6 m 0.4 m 0.2 m Rigid bar D C W 0.5m 40 x 6 mm 50 GPa wable stress = 80 MPa 16 mm dia. bolt with allowable s 6 mm 80 MPa in bearing and 60 MPa The rigid bar A,B,C,D shown in figure is connected to the ground by a hinge at B and to Magnesium bar at A, Aluminum bar at C. the properties of the bars are shown on the figure. all the connections are using 16 mm bolts in single shear. Determine the maximum safe load W that can be applied. Determine the final position of point D.
A piston and cylinder device containg 12 kg of wonter cerries ont a correct Power cycle, the maximum prossure is 2 mpa and the minimum pressuc is 110 KPa , During the isothermal exparsion the water is heated from a quatity of \( 14 \% \) untel it is a saturated vapour, the cycle poduces \( 500 \mathrm{KJ} / \mathrm{kg} \) of work during the Adialatic expansion. a) Sketch the procecs path of the cycle on a \( P-V \) dragam. b) Calculate \( q \) and \( w \) in \( k J \) for each process on the cycle c) Calculate the thermal efficiency of the cycle.
Q4
The beam is horizontal and the springs are unstretched when there is no load on the beam. Suppose that k = 1 kN/m and kB = 2 kN/m (Figure 1) Figure KA 00000 3 m 600 N/m 3 m B - ANNA < 1 of 1 KB D Part A Determine the angle of tilt of the beam when the load is applied. Express your answer in degrees to three significant figures. 17 ΑΣΦ 0= 0.052rad Submit vec Provide Feedback Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining ?
The bar in the figure below is made from standard acrylic plastic (E = 2960 MPa). Compute the total change in length, δof the shaft due to the loadings shown.
A = Tab Problem 1. An ellipse with semi-major axis a = 150 mm and semi-minor axis b = 100 mm is etched on a brass plate. The plate has dimensions 400 x 400 × 20 mm. Uniformly distributed normal stresses ox = -25 MPa and o, = 50 Mpa are applied to the plate. The Young's modulus E = 100 GPa, and Poisson's ratio v = 0.34. (Note: The ellipse remains an ellipse after stretching, but with different semi-major and semi-minor axes.) Find: a) The change in the area of the ellipse. Oy The in the thickness of the plate. b) c) The change AV in the volume of the plate. Ox a. -b- Ox a d) The strain energy, U, stored in the plate. Ty

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS