:) c 2 3 :00 8 to Find RCD

Q: Introduction Explanation of Maximum Power in DC

A: In a d.c. circuit consisting of a resistor connected in series to a voltage source, the current…

Q: Q1: For the network of Figure below, VDD= 9 V. Determine: (а) ID. (b) VS and VDS. (c) VG and VGS.…

A:

Q: Q9. A typical control system is shown in Figure. Assuming R(s) = 1/s; the steady-state error is s+…

A:

Q: Problem 5. Find the range of parameters g and r in which the circuits below are stable: a) о b) gVc…

A:

Q: A second order control system has a damping ratio as 0.6 and natural frequency of oscillations as 11…

A: Given- 2nd order control system- Damping ratio=0.6, Natural frequency ωn=11 rad/sec, To Find- The…

Q: c) Explain the reason for the speedup and slow down of an electron in atomic orbit placed in…

A: In the magnetic field, there are varies changes in the election speed in orbit. The speed of the…

Q: With the aid of diagrams, discuss the procedure to detect zero error and cyclic error in fieldwork.

A: Field work- Field work is typically work that is not done in the main office buy at the customers…

Q: what is the use of DC/DC tension converter DC/DC booster MT3608

A: Types of mostly used DC DC Converter Step up Converter ( Boost converter) Step Down Converter (…

Q: In an On-Off AC Voltage controller, the ON time is 50 cycles and duty cycle is 0.25. The OFF time…

A: Let M be the number of on cycles and N be number of off cycles. Duty cycle=no.on cyclesno.on…

Q: Question L find and draw the therenio eguixaleat ciruit at the output terminals an and b for the…

A: In this question , find thevenin equivalent across terminals ab.... Note:- due to bartleby policy ,…

Q: How to get Multisim to automatically reorganize circuits?

A: Introduction Modularization and reuse are beneficial not only in software development, but also in…

Q: Find i in the network using superposition. 5Ω 10 Ω 2 A 5Ω 4Ω 20 V

A: This theorem is used to find current in any particular branch. To apply this minimum 2 sources are…

Q: 7. Obtain the transfer function for the system given in Figure 2. T«(s) G3(s) G(s) G2(s) 10 540…

A: We have to find transfer function

Q: Which Arc Extinction Method operates by keeping the Arc Resistance low until the Current becomes…

A:

Q: A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of…

A: Given data, Time constant,τ= 10 msec Voltage source V = 10 KV = 10000 V Discharging current is,…

Q: What happened if the DC voltage in the clamping circuit is replaced by an a.c source?

A: What happened if the DC voltage in the clamping circuit is replaced by an a.c source?

Q: find current il in the inductor under the dc conditions any

A: Need to find the current through the inductor at DC condition. The required current can be…

Q: Magnets are the main component in: Select one: capacitors. motors. permanent magnets. ohmmeters.

A: The question is asking to identify the main component in which magnets are used. Magnets are used in…

Q: proximately, how long does it take the circuit to have a current near 5A upon closing of the ritch?…

A:

Q: C = 5 µF C3 = 8 µF C2 = 4 µF C4 = 6 µF C3 = 4 µF DUDACELL VT = 12 V

A: Option c 5.65 volt is correct Please note that 12 volt is parallel with ( 6 and 4 ) 12 volt parallel…

Q: Fill in the blanks: Given the model for position control system, find the value for K1 and K2 so…

A: Given, Position control system is Peak time,tp = 0.5s %overshoot = 3% We need to determine values…

Q: what are standard impluse voltages, mention their values ?

A:

Q: lain the operation of a full subtractor with necessary diagrams. What is the difference between half…

A: Full Subtractor : It is is a combinational circuit that perform subtractor it consist three bits. It…

Q: Design a clamper to perform the function indicated in the given figure. Please upload your solution.

A: Clamper is a circuit which clamps the total signal above or below the reference voltage depending…

Q: The principle operation of LVDT is based on the variation of Select one a. Self inductance b.…

A: Right Answer option C.Mutual Inductance

Q: An inductive load of 100 Ohm and 200mH connected in series to thyristor supplied by 200V dc source.…

A: Given information is that an inductive load is connected in series to thyristor. The supply voltage…

Q: a. A simple DC circuit is shown in Figure 4. If ix=10A, find v1 and iy If v1=6V, find ix and iy. i.…

A: The solution can be achieved as follows.

Q: Cylindrical metallic parabolic trough solar thermal collectors. 1. Does not rotate. 2. It rotates…

A: Cylindrical metallic parabolic trough solar thermal collectors

Q: What are the two necessary conditions for a thyristor to begin conduction? and Once a thyristor…

A: Two necessary conditions for a thyristor to begin conduction is - Forward bias voltage applied…

Q: 2. For the Figure shown below, determine Vx. - 20 100 Vx 40 20V 80 60

A:

Q: A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of…

A: When a switching device is in it's reverse recovery states, various charge carriers recombine. This…

Q: How much resistance must be put in series with a 40-microfarad-capacitor connected to a 110 volt,…

A:

Q: For the figure shown below if the current is moving clockwise around the coil. Which direction does…

A: We use flaming left hand rule to find the direction of motion.